Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › EXHAUST PIPE(w/o DPF)
RM2660E _51 Engine / Hybrid System _052790 1VD-FTV INTAKE / EXHAUST _0255176 EXHAUST PIPE(w/o DPF) A

1VD-FTV INTAKE / EXHAUST  EXHAUST PIPE(w/o DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves and protective glasses when installing the exhaust pipe.

·

The exhaust pipe is extremely hot immediately after the engine has stopped.

·

Confirm that the exhaust pipe has cooled down before removing it.



PROCEDURE

Hide 17292 1.INSTALL OUTLET TURBINE ELBOW LH (w/o Monolithic Converter)

a.
A174835

Set a new gasket to the turbocharger.


b.

Temporarily install the outlet turbine elbow LH with 3 new nuts.


c.

Temporarily install the manifold stay LH with the 3 bolts.


d.

Tighten the 3 nuts of the outlet turbine elbow LH.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


e.

Tighten the 3 bolts of the manifold stay LH.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17291 2.INSTALL OUTLET TURBINE ELBOW RH (w/o Monolithic Converter)

a.
A174836

Set a new gasket to the turbocharger.


b.

Temporarily install the outlet turbine elbow RH with 3 new nuts.


c.

Temporarily install the manifold stay RH with the 3 bolts.


d.

Tighten the 3 nuts of the outlet turbine elbow RH.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


e.

Tighten the 3 bolts of the manifold stay RH.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 18460 3.INSTALL MONOLITHIC CONVERTER ASSEMBLY LH (w/ Monolithic Converter)

a.
A174833

Set a new gasket to the turbocharger.


b.

Temporarily install the monolithic converter LH with 3 new nuts.


c.

Temporarily install the manifold stay LH with the 3 bolts.


d.

Tighten the 3 nuts of the monolithic converter LH.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


e.

Tighten the 3 bolts of the manifold stay LH.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 18450A 4.INSTALL MONOLITHIC CONVERTER ASSEMBLY RH (w/ Monolithic Converter)

a.
A174834

Set a new gasket to the turbocharger.


b.

Temporarily install the monolithic converter RH with 3 new nuts.


c.

Temporarily install the manifold stay RH with the 3 bolts.


d.

Tighten the 3 nuts of the monolithic converter RH.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


e.

Tighten the 3 bolts of the manifold stay RH.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17450B 5.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

a.

Install a new gasket and the front No. 2 exhaust pipe to the monolithic converter/outlet turbine elbow with 2 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


Hide 17410 6.INSTALL FRONT NO. 1 EXHAUST PIPE ASSEMBLY

a.

Install a new gasket and the front No. 1 exhaust pipe to the converter/outlet turbine elbow with 2 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


Hide 17420 7.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.
A128853

Check the free length.

i.

Using a vernier caliper, measure the free length of the compression spring.

Free length:

43 mm (1.69 in.)


If the free length is less that the minimum, replace the compression spring.



b.

Connect the center exhaust pipe to the 3 exhaust pipe supports.


c.

Set 2 new gaskets to the front No. 1 and No. 2 exhaust pipes.


d.

Install the center exhaust pipe with the 4 bolts and 2 compression springs.

Torque:
for center exhaust pipe and front No. 1 exhaust pipe : 43 N*m (438 kgf*cm, 32 ft.*lbf)
for center exhaust pipe and front No. 2 exhaust pipe : 48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 17430 8.INSTALL TAILPIPE ASSEMBLY

a.
A167906E07
1.75,3.469 1.031,3.719 1.031,3.719 0.865,3.719 true 2.635,0.448 2.875,0.594 0.24,0.146 10 false 30° 0.271,1.01 0.823,1.156 0.552,0.146 10 false LH Side 0.719,0.156 1.146,0.333 0.427,0.177 10 false Upper 0.125,2.844 0.49,3 0.365,0.156 10 false Front 0.313,3.635 0.802,3.792 0.49,0.156 10 false Gasket

Connect the tailpipe to the 2 exhaust pipe supports.


b.

Set a new gasket to the center exhaust pipe.


c.

Connect the tailpipe to the center exhaust pipe with a new clamp.

HINT:

Install the clamp within the angle range shown in the illustration.



d.

Tighten the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 9.INSPECT FOR EXHAUST GAS LEAK

Hide 51442 10.INSTALL NO. 2 ENGINE UNDER COVER

a.
C173930

Install the under cover the with the 6 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 53739A 11.INSTALL FRONT FENDER APRON SEAL REAR LH

a.
A177005

Install the fender apron seal with the 4 clips.


Hide 53738A 12.INSTALL FRONT FENDER APRON SEAL REAR RH

a.
A177002

Install the fender apron seal with the 4 clips.