Home › Engine / Hybrid System › 1GR-FE (STARTING) › STARTER
RM2660E _51 Engine / Hybrid System _052800 1GR-FE STARTING _0255230 STARTER G

1GR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A219641E05
0.313,1.656 0.479,1.656 0.479,1.656 1.01,1.479 false 0.5,0.26 0.667,0.26 0.667,0.26 1.333,0.708 false 0.323,0.156 0.5,0.323 0.177,0.167 10 false *1 0.135,1.573 0.333,1.75 0.198,0.177 10 false *2

Connect the battery to the starter as shown in the illustration. Then check that the clutch pinion gear moves outward.

Text in Illustration
*1 Terminal 50
*2 Terminal C

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



c.
A219642E04
1.021,1.469 0.5,1.698 0.5,1.698 0.396,1.698 false 0.24,1.604 0.417,1.802 0.177,0.198 10 false *1

Perform a holding test.

i.

Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

Text in Illustration
*1 Terminal C

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



d.
A219643

Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



e.
A218205E02
1.064,0.567 0.651,0.076 0.651,0.076 0.555,0.076 false 0.285,0 0.479,0.163 0.194,0.163 10 *2 2.056,1.599 2.233,1.767 0.177,0.167 10 *1 1.425,0.895 1.879,1.696 1.879,1.696 2.048,1.696 false

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


ii.

Connect the battery and an ammeter to the starter as shown in the illustration.

Text in Illustration
*1 Terminal 50
*2 Terminal 30


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

Specified current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the resistance.

i.
A218206E02
2.607,2.484 2.966,1.592 2.966,1.592 3.125,1.592 false 0.846,1.489 1.027,1.643 0.181,0.154 10 *2 3.141,1.505 3.334,1.661 0.193,0.156 10 *1 1.351,2.095 1.18,1.581 1.18,1.581 1.055,1.581 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


Text in Illustration
*1 Terminal 50
*2 Terminal C

If the result is not as specified, replace the magnet starter switch assembly.


ii.
A218207E02
2.05,1.797 1.806,0.756 1.806,0.756 1.669,0.756 false 2.571,2.467 2.892,1.618 2.892,1.618 2.976,1.618 false 3.005,1.53 3.195,1.693 0.191,0.163 10 *1 1.412,0.652 1.607,0.830 0.195,0.178 10 *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


Text in Illustration
*1 Terminal 50
*2 Switch Body

If the result is not as specified, replace the magnet starter switch assembly.



Hide 3.INSPECT BRUSH

a.
A384999E01
0.01,0.063 0.229,0.26 0.219,0.198 10 false *a 0.01,2.781 0.229,2.979 0.219,0.198 10 false *b 0.583,2.104 0.802,2.302 0.219,0.198 11 false *1 2.438,4.281 2.656,4.479 0.219,0.198 10 false *1

Using a vernier caliper, measure the brush length.

Standard length:

15.5 mm (0.610 in.)


Minimum length:

8.5 mm (0.335 in.)


Text in Illustration
*1 Length
*a Brush Holder Side
*b Starter Yoke Side

If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check the brush spring load.

i.
ST00019E22
0.771,1.406 0.927,1.406 0.927,1.406 1.323,1.719 false 2.479,1.094 2.333,1.094 2.333,1.094 2.25,1.281 false 0.604,1.323 0.917,1.521 0.313,0.198 10 false *1 2.531,1 2.844,1.198 0.313,0.198 10 false *2

Take a pull scale reading immediately after the brush spring separates from the brush.

Standard spring load:

18 to 24 N (1.8 to 2.4 kgf, 4.0 to 5.3 lbf)


Minimum spring load:

12 N (1 kgf, 2.7 lbf)


Text in Illustration
*1 Brush
*2 Brush Spring

If the spring load is less than the minimum, replace the starter brush holder assembly.



b.
G036824

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush holder - Negative (-) brush holder Always 10 Ω or higher


If the result is not as specified, replace the starter brush holder assembly.



Hide 28120 5.INSPECT STARTER YOKE ASSEMBLY

a.

Check the resistance.

i.
A050093

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lead wire - Brush Always Below 1 Ω


If the result is not as specified, replace the starter yoke assembly.


ii.
A050418

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter yoke body - Brush Always 10 kΩ or higher


If the result is not as specified, replace the starter yoke assembly.



Hide 28160 6.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

If necessary, replace the starter armature assembly.


b.

Check the resistance.

i.
A225234E01
0.362,1.023 0.545,1.199 0.184,0.176 10 *1 1.196,1.559 0.739,1.128 0.739,1.128 0.578,1.128 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


Text in Illustration
*1 Segment

If the result is not as specified, replace the starter armature assembly.


ii.
A225235E01
2.384,0.454 2.578,0.634 0.194,0.180 10 *2 0.328,1.03 0.522,1.192 0.194,0.162 10 *1 1.195,1.554 0.685,1.13 0.685,1.13 0.55,1.13 false 1.974,1.249 2.24,0.549 2.24,0.549 2.364,0.549 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


Text in Illustration
*1 Segment
*2 Coil Core

If the result is not as specified, replace the starter armature assembly.



c.
A219195

Check the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum circle runout:

0.05 mm (0.00197 in.)


If the circle runout is more than the maximum, replace the starter armature assembly.



d.
A219196

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

30.0 mm (1.18 in.)


Minimum diameter:

29.0 mm (1.14 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


e.
A102634

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.6 mm (0.0236 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.


Hide 28011 7.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A223418

Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

Text in Illustration
V100135

Free
V100136

Lock

If the result is not as specified, replace the starter clutch sub-assembly.


b.

Turn the pinion gear by hand while applying inward force and check the movement of the bearing.

If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.