Home › Engine / Hybrid System › 3UR-FE (STARTING) › STARTER
RM2660E _51 Engine / Hybrid System _052801 3UR-FE STARTING _0255233 STARTER A

3UR-FE STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A258326

Apply high-temperature grease to the areas of the starter pinion drive lever indicated in the illustration.

Text in Illustration
V100135

High-temperature grease


b.

Install the starter pinion drive lever and rubber seal to the starter center bearing clutch.


c.

Install the starter center bearing clutch together with the starter pinion drive lever and rubber seal to the starter drive housing.


d.
A258327

Apply high-temperature grease to the planetary gears and pins of the starter center bearing clutch.

Text in Illustration
V100135

High-temperature grease


e.

Install the 3 planetary gears.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature to the starter yoke.

NOTICE:

The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed, causing the magnet to break.



Hide 28140 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A215977

Push out the 4 brushes from the brush holder so that they are held in place by the springs as shown in the illustration.


b.
A215968

Install the brush holder to the starter armature and push in the 4 brushes.

NOTICE:

Check that the positive (+) lead wires are not grounded.



c.
U115374E01
0.876,0.194 1.04,0.194 1.04,0.194 1.55,0.896 false 0.688,0.099 0.846,0.255 0.158,0.156 10 *1 0.585,0.528 0.753,0.682 0.168,0.154 10 *2 0.785,0.617 0.866,0.617 0.866,0.617 1.324,0.974 false 2.641,1.194 2.805,1.345 0.164,0.151 10 *3 2.624,1.287 2.516,1.287 2.516,1.287 2.1,0.944 false

Insert the grommet between the positive side and negative side.

Text in Illustration
*1 Grommet
*2 Negative Side
*3 Positive Side


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.
A258328E02
2.17,0.437 2.339,0.592 0.169,0.155 10 *1 1.705,0.78 2.048,0.53 2.048,0.53 2.158,0.53 false 1.069,1.431 1.244,1.593 0.176,0.162 10 *2 1.507,1.157 1.383,1.511 1.383,1.511 1.268,1.511 false

Install the starter armature plate to the starter yoke.

Text in Illustration
*1 Key A
*2 Key B

NOTICE:

Install the starter armature plate so that the keyway is positioned between key A and key B.



b.

Install the commutator end frame with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


c.
A258329E02
0.751,1.436 0.921,1.593 0.170,0.156 10 *1 0.95,1.036 0.828,1.346 0.828,1.346 0.828,1.434 false 1.577,1.639 1.745,1.791 0.168,0.152 10 *2 2.014,1.437 1.897,1.728 1.897,1.728 1.775,1.728 false

Align the key of the starter yoke with the keyway located on the starter drive housing.

Text in Illustration
*1 Keyway
*2 Key


d.

Using a T25 "TORX" socket wrench, install the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 5.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A449553

Apply high-temperature grease to the plunger hook.

Text in Illustration
V100135

High-temperature grease


b.

Hang the plunger of the magnet starter switch onto the drive lever from the upper side.


c.

Install the magnet starter switch with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Connect the lead wire to the magnet starter switch with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)