Home › Engine / Hybrid System › 1UR-FE (STARTING) › STARTER
RM2660E _51 Engine / Hybrid System _052802 1UR-FE STARTING _0255237 STARTER G

1UR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to avoid burning out the coil.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A258295E02
2.379,0.221 2.556,0.382 0.177,0.161 10 *2 2.129,0.744 2.263,0.303 2.263,0.303 2.373,0.303 false 2.389,2.197 2.558,2.349 0.169,0.152 10 *1 2.124,1.11 2.265,2.285 2.265,2.285 2.381,2.285 false

Connect the battery to the starter as shown in the illustration. Then check that the clutch pinion gear moves outward.

Text in Illustration
*1 Terminal C
*2 Terminal 50

If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.



c.

Perform a holding test.

i.
A258296E02
2.41,2.154 2.563,2.307 0.153,0.153 10 *1 2.124,1.11 2.287,2.239 2.287,2.239 2.398,2.239 false

Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

Text in Illustration
*1 Terminal C

If the clutch pinion gear moves inward, replace the magnet starter switch assembly.



d.

Inspect the clutch pinion gear return.

i.
A258297

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear moves inward.

If the clutch pinion gear does not move inward, replace the magnet starter switch assembly.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A258298E02
2.893,1.777 3.062,1.926 0.170,0.148 10 *2 1.5,1.722 1.665,1.871 0.165,0.148 10 *1 2.042,1.046 1.811,1.802 1.811,1.802 1.692,1.802 false 2.157,0.958 2.774,1.862 2.774,1.862 2.886,1.862 false

Connect the battery and an ammeter to the starter as shown in the illustration.

Text in Illustration
*1 Terminal 30
*2 Terminal 50


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

150 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the surface of the commutator for dirt and burns.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

If necessary, replace the starter armature assembly.


b.

Inspect the commutator for an open circuit.

i.
A215965E02
2.709,1.205 2.869,1.370 0.161,0.165 10 *1 1.182,1.6 1.345,1.753 0.163,0.154 10 *1 1.392,1.676 1.494,1.676 1.494,1.676 1.993,1.153 false 2.657,1.29 2.577,1.29 2.577,1.29 2.187,0.877 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


Text in Illustration
*1 Segment

If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for a short circuit.

i.
A215966E02
2.583,1.55 2.774,1.709 0.190,0.159 10 *2 2.548,1.641 2.485,1.641 2.485,1.641 2.071,1.169 false 0.578,0.703 0.744,0.875 0.166,0.172 10 *1 0.797,0.784 0.878,0.784 0.878,0.784 1.319,1.089 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


Text in Illustration
*1 Coil Core
*2 Segment

If the result is not as specified, replace the starter armature assembly.



d.
A215958

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

29.0 mm (1.14 in.)


Minimum diameter:

28.0 mm (1.10 in.)


HINT:

Be sure to measure the commutator diameter at the ridges.


If the diameter is less than the minimum, replace the starter armature assembly.


e.

Check the commutator circle runout.

i.

Place the armature shaft on V-blocks.


ii.
A215967

Using a dial indicator, measure the circle runout.

Maximum commutator runout:

0.05 mm (0.00197 in.)


If the commutator runout is more than the maximum, replace the starter armature assembly.



f.
A062965

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.4 mm (0.0157 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


HINT:

Be sure to measure the commutator undercut depth at a cutout.


If the undercut depth is less than the minimum, replace the starter armature assembly.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A215975

Using a vernier caliper, measure the brush length.

Standard length:

14.4 mm (0.567 in.)


Minimum length:

9.0 mm (0.354 in.)


HINT:

Be sure to measure the brush lengths at the protrusions.


If the brush length is less than the minimum, replace the starter brush holder assembly.


b.

Inspect the load of the brush spring.

i.
A115032E02
0.952,1.592 1.122,1.753 0.170,0.161 10 *1 2.546,1.117 2.723,1.277 0.178,0.161 10 *2 1.398,1.838 1.269,1.689 1.269,1.689 1.145,1.689 false 2.301,1.381 2.426,1.204 2.426,1.204 2.542,1.204 false

Take a pull scale reading immediately after the brush spring separates from the brush.

Standard spring load:

22 to 27 N (2 to 3 kgf, 5.0 to 6.1 lbf)


Minimum spring load:

14 N (1 kgf, 3.1 lbf)


Text in Illustration
*1 Brush
*2 Brush Spring

If the load is less than the minimum, replace the starter brush holder assembly.



Hide 28021 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth of the planetary gears and starter center bearing clutch for wear or damage.

If any planetary gear is damaged, replace the planetary gears. If any teeth of the starter center bearing clutch are damaged, replace the starter center bearing clutch sub-assembly.


b.
A221357

Check the movement of the clutch pinion gear.

i.

Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

Text in Illustration
V100135

Free
V100136

Lock

If the clutch pinion gear cannot be turned clockwise smoothly, or does not lock in the counterclockwise direction, replace the starter center bearing clutch sub-assembly.



Hide 28150 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Inspect the pull-in coil.

i.
A162877E03
2.463,0.472 2.651,0.636 0.188,0.164 10 *2 1.261,1.774 1.446,1.940 0.184,0.166 10 *1 1.763,1.508 1.587,1.872 1.587,1.872 1.473,1.872 false 2.022,1.02 2.36,0.554 2.36,0.554 2.454,0.554 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


Text in Illustration
*1 Terminal C
*2 Terminal 50

If the result is not as specified, replace the magnet starter switch assembly.



b.

Inspect the holding coil.

i.
A162878E03
2.515,0.69 2.673,0.839 0.158,0.149 10 *1 1.987,1.39 2.427,0.764 2.427,0.764 2.505,0.764 false 0.584,0.084 0.742,0.233 0.158,0.149 10 *2 1.079,0.617 0.888,0.175 0.888,0.175 0.767,0.175 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


Text in Illustration
*1 Terminal 50
*2 Switch Body

If the result is not as specified, replace the magnet starter switch assembly.