Home › Engine / Hybrid System › 1UR-FE (STARTING) › ENGINE SWITCH › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052802 1UR-FE STARTING _0255238 ENGINE SWITCH G

1UR-FE STARTING  ENGINE SWITCH  INSPECTION  


PROCEDURE

Hide 89611 1.INSPECT ENGINE SWITCH

A129763E09
0.058,0.821 0.359,0.977 0.302,0.156 10 SS1 0.114,0.11 0.304,0.266 0.191,0.156 10 *a 1.803,0.208 2.178,0.389 0.375,0.181 10 GND 2.89,0.208 3.219,0.370 0.330,0.163 10 SS2 2.817,0.289 2.688,0.289 2.688,0.289 2.434,0.914 false 1.751,0.306 1.614,0.306 1.614,0.306 1.416,0.905 false 0.41,0.903 0.757,0.903 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (SS1) - 5 (GND)
2 (SS2) - 5 (GND)
Not pushed 10 kΩ or higher
7 (SS1) - 5 (GND)
2 (SS2) - 5 (GND)
Pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(Engine Switch)

If the result is not as specified, replace the engine switch.


b.

Apply battery voltage between the terminals of the switch, and check the illumination condition of the switch.

HINT:
·

If the positive (+) lead and the negative (-) lead are incorrectly connected, the engine switch indicator will not illuminate.


·

If the voltage is too low, the indicator will not illuminate.



OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 11 (SWIL)
Battery negative (-) → Terminal 5 (GND)
Illuminates (illumination of lettering)
Battery positive (+) → Terminal 12 (INDS)
Battery negative (-) → Terminal 5 (GND)
Illuminates (green)
Battery positive (+) → Terminal 13 (INDW)
Battery negative (-) → Terminal 5 (GND)
Illuminates (amber)


A385036E01
1.635,0.5 1.979,0.125 1.979,0.125 2.167,0.125 false 3.094,0.927 3.281,0.927 3.281,0.927 4.115,1.24 false 3.75,0.354 3.927,0.354 3.927,0.354 4.385,1.281 false 6.021,0.896 5.885,0.896 5.885,0.896 4.646,1.271 false 4.688,0.24 4.542,0.24 4.542,0.24 4.417,0.906 false 2.26,0.042 2.573,0.24 0.313,0.198 10 false *1 3.688,0.021 4,0.219 0.313,0.198 10 false *a 2.688,0.854 3.156,1.063 0.469,0.208 10 false INDW 3.396,0.26 3.865,0.469 0.469,0.208 10 false INDS 4.74,0.146 5.208,0.354 0.469,0.208 10 false GND 6.052,0.823 6.521,1.031 0.469,0.208 10 false SWIL

Text in Illustration
*1 Indicator - -
*a Component without harness connected
(Engine Switch)
- -

If the result is not as specified, replace the engine switch.