Home › Engine / Hybrid System › 1VD-FTV (STARTING) › STARTER
RM2660E _51 Engine / Hybrid System _052803 1VD-FTV STARTING _0255243 STARTER A

1VD-FTV STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28011 1.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.

Apply high-temperature grease to the parts indicated by the arrows in the illustration.

U162882E01
0.328,2.452 1.928,2.631 1.600,0.179 10 High-temperature grease


b.

Install the starter clutch into the magnet starter switch.

NOTICE:

Make sure that the bearing does not disengage from the starter clutch.



c.

Install the 3 starter washers and pinion drive lever with the snap ring.


Hide 28110 2.INSTALL STARTER DRIVE HOUSING ASSEMBLY

a.
A175309E01
0.055,0.421 0.915,0.610 0.861,0.189 10 Seal Packing 1.639,0.682 1.156,0.529 false 1.156,0.529 1.097,0.529 false

Apply a light coat of seal packing to the surface of the starter drive housing that contacts the starter magnet switch.

Seal packing:

Toyota Genuine Seal Packing 1121C, Three Bond 1121C or equivalent



b.
A175306

Install the starter drive housing with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28256 3.INSTALL STARTER INTERNAL GEAR

a.
U163255E01
0.428,1.763 2.028,1.941 1.600,0.179 10 High-temperature grease

Apply high-temperature grease to the portion indicated by the arrow in the illustration.


b.
A168833

Install the starter internal gear.

NOTICE:

Make sure the internal gear protrusion indicated by the arrow in the illustration is aligned with the groove on the bottom side of the magnet starter switch.



c.
U163019E01
0.424,1.753 2.024,1.931 1.600,0.179 10 High-temperature grease

Apply high-temperature grease to the planetary gears.


d.

Install the 3 starter planetary gears.


Hide 28160 4.INSTALL STARTER ARMATURE ASSEMBLY

a.
A163701

Install the starter washer.

NOTICE:

Make sure that the washer is securely seated in the groove.



b.
U163256E01
0.388,1.767 1.988,1.946 1.600,0.179 10 High-temperature grease

Apply high-temperature grease to the portion indicated by the arrow in the illustration.


c.
A175302

Install the starter plate.


d.
U163257E01
0.378,1.795 1.978,1.973 1.600,0.179 10 High-temperature grease

Apply high-temperature grease to the portion indicated by the arrow in the illustration.


e.
A175301

Install the starter armature to the starter plate.


Hide 28120 5.INSTALL STARTER YOKE ASSEMBLY

a.
A163097E01
0.021,0.213 0.841,0.418 0.821,0.204 10 New O-Ring 1.417,0.811 1.042,0.329 false 1.037,0.325 2.041,0.655 false

Install 2 new O-rings to the starter yoke.


b.
A165498

Install the starter yoke to the magnet starter switch.


Hide 28140 6.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Place the brush holder on the starter armature.


b.
A163085

Using a screwdriver, hold the starter brush spring back and connect the 4 starter brushes to the starter brush holder.

NOTICE:

Check that the positive (+) lead wires are not grounded.



c.

Install the starter brush holder into the starter armature.


d.
U162883E01
0.406,1.75 2.006,1.929 1.600,0.179 10 High-temperature grease

Apply high-temperature grease to the portion indicated by the arrow in the illustration.


e.
A175300E01
0.115,0.583 0.833,0.748 0.718,0.165 10 Terminal C 1.477,0.666 0.971,0.666 false

Install the commutator end frame with the 2 screws.

Torque:
3.9 N*m (40 kgf*cm, 35 in.*lbf)


f.

Install the 2 through bolts.

Torque:
17 N*m (173 kgf*cm, 12 ft.*lbf)


g.

Install the nut to terminal C.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


h.
A177688E01
0.327,1.379 1.076,1.536 0.749,0.157 10 White Mark 1.335,0.023 1.748,0.179 0.414,0.157 10 Mark 2.272,2.76 2.686,2.917 0.414,0.157 10 Mark 0.011,2.984 0.760,3.140 0.749,0.157 10 White Mark 1.327,2.74 0.959,3.091 false 0.962,3.091 0.914,3.091 false 0.684,0.68 0.684,1.369 false 0.813,0.461 1.209,0.116 false 1.209,0.116 1.314,0.116 false 1.607,2.382 2.166,2.852 false 2.164,2.852 2.235,2.852 false

Install the 2 starter hoses to the starter.


Hide 28213 7.INSTALL STARTER CLUTCH PINION

a.
A175310

Install the spring, starter clutch pinion and pinion stop collar with the snap ring.