Home › Engine / Hybrid System › 1VD-FTV (STARTING) › RELAY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052803 1VD-FTV STARTING _0255244 RELAY G

1VD-FTV STARTING  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 28300 1.INSPECT STARTER RELAY (ST)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 28300D 2.INSPECT STARTER CUT RELAY (ST CUT)

a.
A385000E01
2.021,0.75 1.781,0.344 false 2.583,0.76 2.896,0.365 false 2.427,1.115 3.052,1.115 false 2.427,1.594 3.042,1.594 false 0.26,0.771 0.417,0.969 0.156,0.198 10 false 5 0.271,1.281 0.427,1.479 0.156,0.198 10 false 1 1.156,1.281 1.313,1.479 0.156,0.198 10 false 2 1.156,0.771 1.313,0.969 0.156,0.198 10 false 3 2.938,0.188 3.094,0.385 0.156,0.198 10 false 2 1.688,0.177 1.844,0.375 0.156,0.198 10 false 1 3.115,1.021 3.271,1.219 0.156,0.198 10 false 5 3.125,1.51 3.281,1.708 0.156,0.198 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 28610 3.INSPECT NO. 1 GLOW RELAY (GLOW 1)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 19850 4.INSPECT NO. 2 GLOW RELAY (GLOW 2)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 82733A 5.INSPECT MAIN BODY ECU (ACC RELAY)

A385001E02
1.594,0.969 1.938,1.198 0.344,0.229 3.646,3.177 4.083,3.385 0.438,0.208 1.76,1.656 1.865,1.917 false 3.24,3.958 3.146,4.24 false 3.76,3.865 3.906,4.219 false 4.427,3.698 4.594,4.25 false 1.823,1.927 1.979,2.125 0.156,0.198 10 false 1 1.677,0.99 1.896,1.177 0.219,0.188 10 false 2A 3.781,3.198 4.094,3.396 0.313,0.198 10 false 2D 3.094,4.281 3.406,4.479 0.313,0.198 10 false 62 3.844,4.271 4.156,4.469 0.313,0.198 10 false 45 4.563,4.292 4.875,4.49 0.313,0.198 10 false 8 0.115,0.115 3.854,0.313 3.74,0.198 10 false Component without harness connected: (Main Body ECU)

a.

Measure the resistance of the ACC relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-1 - 2D-8 Battery voltage not applied between 2D-45 and 2D-62 10 kΩ or higher
Battery voltage applied between 2D-45 and 2D-62 Below 1 Ω


If the result is not as specified, replace the main body ECU.