Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL MAIN SWITCH › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255248 CRUISE CONTROL MAIN SWITCH G

CRUISE CONTROL  CRUISE CONTROL MAIN SWITCH  INSPECTION  


PROCEDURE

Hide 84632 1.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY

a.

Measure the resistance (for vehicles without vehicle-to-vehicle distance control mode).

E155225E02
0.965,2.539 0.976,2.978 false 1.35,2.537 1.463,2.972 false 0.796,2.972 1.165,3.166 0.368,0.194 10 CCS 1.343,2.972 1.761,3.166 0.418,0.194 10 ECC 2.59,2.006 3.136,2.201 0.546,0.194 10 (CCS) 2.59,2.684 3.136,2.878 0.546,0.194 10 (ECC) 3.809,2.377 4.263,2.572 0.453,0.194 10 MAIN 4.539,2.377 5.018,2.572 0.478,0.194 10 +RES 5.281,2.377 5.784,2.572 0.502,0.194 10 -SET 6.015,2.377 6.626,2.572 0.611,0.194 10 CANCEL 0.052,0 2.547,0.720 2.495,0.720 10 Component without harness connected: (Cruise Control Main Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (ECC) - 3 (CCS) +RES 235 to 245 Ω
1 (ECC) - 3 (CCS) -SET 620 to 640 Ω
1 (ECC) - 3 (CCS) CANCEL 1510 to 1570 Ω
1 (ECC) - 3 (CCS) Main switch off 1 MΩ or higher
1 (ECC) - 3 (CCS) Main switch on Below 2.5 Ω


If the result is not as specified, replace the cruise control main switch assembly.




b.

Measure the resistance (for vehicles with vehicle-to-vehicle distance control mode).

E155226E03
1.146,2.615 1.146,2.948 false 1.344,2.615 1.688,2.938 false 0.927,2.604 0.573,2.948 false 1.021,2.969 1.417,3.167 0.396,0.198 10 false R/N 0.417,2.906 0.771,3.104 0.354,0.198 10 false CCS 1.531,2.948 1.927,3.146 0.396,0.198 10 false ECC 2.344,1.979 2.792,2.177 0.448,0.198 10 false (R/N) 2.344,2.635 2.792,2.833 0.448,0.198 10 false (CCS) 2.99,2.125 3.49,2.323 0.5,0.198 10 false MODE 3.615,2.354 4.052,2.552 0.438,0.198 10 false MAIN 4.333,2.354 4.771,2.552 0.438,0.198 10 false +RES 5.042,2.354 5.458,2.552 0.417,0.198 10 false -SET 5.771,2.354 6.365,2.552 0.594,0.198 10 false CANCEL 6.479,2.146 6.948,2.344 0.469,0.198 10 false (ECC) 0.052,0 2.552,0.719 2.5,0.719 10 false Component without harness connected: (Cruise Control Main Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (ECC) - 3 (CCS) +RES 235 to 245 Ω
1 (ECC) - 3 (CCS) -SET 620 to 640 Ω
1 (ECC) - 3 (CCS) CANCEL 1510 to 1570 Ω
1 (ECC) - 3 (CCS) Main switch off 1 MΩ or higher
1 (ECC) - 3 (CCS) Main switch on Below 2.5 Ω
3 (CCS) - 2 (R/N) Main switch on and mode switch on Below 2.5 Ω


If the result is not as specified, replace the cruise control main switch assembly.