Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255249 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM (3UR-FE)


U165991E02
2.448,0.167 2.74,0.323 0.292,0.156 10 false C45 5.458,0.167 5.75,0.323 0.292,0.156 10 false A38

HINT:

As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.


a.

Disconnect the A38 and C45 ECM connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-16 (TC) - Body ground V - Body ground Terminal TC of DLC3 Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
C45-81 (E1) - Body ground W-B - Body ground ECM ground Always Below 1 Ω
C45-27 (D) - Body ground G - Body ground Park/neutral position switch signal Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38-38 (SFTU) - Body ground V - Body ground Park/neutral position switch signal Ignition switch ON
Shift lever in S
Below 1 Ω
Ignition switch ON
Shift lever in +
10 kΩ or higher
A38-25 (S) - Body ground W - Body ground Park/neutral position switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38-27 (SFTD) - Body ground L - Body ground Park/neutral position switch signal Ignition switch ON
Shift lever in S
10 kΩ or higher
Ignition switch ON
Shift lever in -
Below 1 Ω
A38-36 (STP) - Body ground R - Body ground Stop light signal Ignition switch ON
Brake pedal depressed
11 to 14 V
Ignition switch ON
Brake pedal released
Below 1 V
A38-35 (ST1-) - Body ground P - Body ground Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
Below 1 V
Ignition switch ON
Brake pedal released
11 to 14 V
A38-45 (CCS) - Body ground L - Body ground Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch held on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



CHECK ECM (1UR-FE)


U165990E01
2.22,0.153 2.513,0.313 0.293,0.161 10 C45 2.583,0.153 2.738,0.313 0.155,0.161 10 *1 5.493,0.153 5.648,0.313 0.155,0.161 10 *1 0.035,2.493 0.766,2.654 0.731,0.161 10 *2: for RHD 0.035,2.23 0.766,2.390 0.731,0.161 10 *1: for LHD 2.986,0.153 3.279,0.313 0.293,0.161 10 C46 3.349,0.153 3.503,0.313 0.155,0.161 10 *2 5.117,0.153 5.410,0.313 0.293,0.161 10 A38 6.19,0.153 6.345,0.313 0.155,0.161 10 *2 5.814,0.153 6.106,0.313 0.293,0.161 10 A52

HINT:

As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.


a.

Disconnect the A38*1 and C45*1 or A52*2 and C46*2 ECM connectors.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38*1-16 (TC) - Body ground
A52*2-16 (TC) - Body ground
V - Body ground*3
V-W - Body ground*4
Terminal TC of DLC3 Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground ECM ground Always Below 1 Ω
C45*1-27 (D) - Body ground
C46*2-27 (D) - Body ground
G - Body ground Park/neutral position switch signal Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38*1-38 (SFTU) - Body ground
A52*2-38 (SFTU) - Body ground
Y - Body ground*3
V - Body ground*4
Park/neutral position switch signal Ignition switch ON
Shift lever in S
Below 1 Ω
Ignition switch ON
Shift lever in "+"
10 kΩ or higher
A38*1-25 (S) - Body ground
A52*2-25 (S) - Body ground
W - Body ground Park/neutral position switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38*1-27 (SFTD) - Body ground
A52*2-27 (SFTD) - Body ground
L - Body ground Park/neutral position switch signal Ignition switch ON
Shift lever in S
10 kΩ or higher
Ignition switch ON
Shift lever in "-"
Below 1 Ω
A38*1-36 (STP) - Body ground
A52*2-36 (STP) - Body ground
R - Body ground Stop light signal Ignition switch ON
Brake pedal depressed
11 to 14 V
Ignition switch ON
Brake pedal released
Below 1 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
R-W - Body ground*3
P - Body ground*4
Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
Below 1 V
Ignition switch ON
Brake pedal released
11 to 14 V
A38*1-45 (CCS) - Body ground
A52*2-45 (CCS) - Body ground
L - Body ground Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch held on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.

HINT:
·

*1: for LHD

·

*2: for RHD

·

*3: Model code: URJ202L-GNTEKC

·

*4: Model code except: URJ202L-GNTEKC





CHECK ECM (1GR-FE)


U165990E01
2.22,0.153 2.513,0.313 0.293,0.161 10 C45 2.583,0.153 2.738,0.313 0.155,0.161 10 *1 5.493,0.153 5.648,0.313 0.155,0.161 10 *1 0.035,2.493 0.766,2.654 0.731,0.161 10 *2: for RHD 0.035,2.23 0.766,2.390 0.731,0.161 10 *1: for LHD 2.986,0.153 3.279,0.313 0.293,0.161 10 C46 3.349,0.153 3.503,0.313 0.155,0.161 10 *2 5.117,0.153 5.410,0.313 0.293,0.161 10 A38 6.19,0.153 6.345,0.313 0.155,0.161 10 *2 5.814,0.153 6.106,0.313 0.293,0.161 10 A52

HINT:

As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.


a.

Disconnect the A38*1 and C45*1 or A52*2 and C46*2 ECM connectors.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38*1-16 (TC) - Body ground
A52*2-16 (TC) - Body ground
V-W - Body ground*3
V - Body ground*4
Terminal TC of DLC3 Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground ECM ground Always Below 1 Ω
C45*1-27 (D) - Body ground
C46*2-27 (D) - Body ground
G - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38*1-38 (SFTU) - Body ground Y - Body ground*3
V - Body ground*4
Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
Below 1 Ω
Ignition switch ON
Shift lever in "+"
10 kΩ or higher
A38*1-25 (S) - Body ground W - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38*1-27 (SFTD) - Body ground L - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
10 kΩ or higher
Ignition switch ON
Shift lever in "-"
Below 1 Ω
A38*1-36 (STP) - Body ground
A52*2-36 (STP) - Body ground
R - Body ground Stop light signal Ignition switch ON
Brake pedal depressed
11 to 14 V
Ignition switch ON
Brake pedal released
Below 1 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
R-W - Body ground*3
P - Body ground*4
Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
Below 1 V
Ignition switch ON
Brake pedal released
11 to 14 V
A38*1-45 (CCS) - Body ground
A52*2-45 (CCS) - Body ground
L - Body ground Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch held on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.

HINT:
·

*1: for LHD

·

*2: for RHD

·

*3: Model code: GRJ200L-GNANKC

·

*3: Model code except: GRJ200L-GNANKC





CHECK ECM (1VD-FTV, w/ DPF)


U165990E01
2.22,0.153 2.513,0.313 0.293,0.161 10 C45 2.583,0.153 2.738,0.313 0.155,0.161 10 *1 5.493,0.153 5.648,0.313 0.155,0.161 10 *1 0.035,2.493 0.766,2.654 0.731,0.161 10 *2: for RHD 0.035,2.23 0.766,2.390 0.731,0.161 10 *1: for LHD 2.986,0.153 3.279,0.313 0.293,0.161 10 C46 3.349,0.153 3.503,0.313 0.155,0.161 10 *2 5.117,0.153 5.410,0.313 0.293,0.161 10 A38 6.19,0.153 6.345,0.313 0.155,0.161 10 *2 5.814,0.153 6.106,0.313 0.293,0.161 10 A52

HINT:

As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.


a.

Disconnect the A38*1 and C45*1 or A52*2 and C46*2 ECM connectors.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38*1-27 (TC) - Body ground
A52*2-27 (TC) - Body ground
V - Body ground Terminal TC of DLC3 Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground ECM ground Always Below 1 Ω
C45*1-28 (D) - Body ground
C46*2-28 (D) - Body ground
G - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38*1-38 (SFTU) - Body ground
A52*2-38 (SFTU) - Body ground
V - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
Below 1 Ω
Ignition switch ON
Shift lever in "+"
10 kΩ or higher
A38*1-25 (S) - Body ground
A52*2-25 (S) - Body ground
W - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38*1-37 (SFTD) - Body ground
A52*2-37 (SFTD) - Body ground
L - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
10 kΩ or higher
Ignition switch ON
Shift lever in "-"
Below 1 Ω
A38*1-13 (STP) - Body ground
A52*2-13 (STP) - Body ground
R - Body ground Stop light signal Ignition switch ON
Brake pedal depressed
11 to 14 V
Ignition switch ON
Brake pedal released
Below 1 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
P - Body ground Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
Below 1 V
Ignition switch ON
Brake pedal released
11 to 14 V
A38*1-40 (CCS) - Body ground
A52*2-40 (CCS) - Body ground
L - Body ground Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch hed on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.

HINT:
·

*1: for LHD

·

*2: for RHD





CHECK ECM (1VD-FTV, w/o DPF)


U165990E01
2.22,0.153 2.513,0.313 0.293,0.161 10 C45 2.583,0.153 2.738,0.313 0.155,0.161 10 *1 5.493,0.153 5.648,0.313 0.155,0.161 10 *1 0.035,2.493 0.766,2.654 0.731,0.161 10 *2: for RHD 0.035,2.23 0.766,2.390 0.731,0.161 10 *1: for LHD 2.986,0.153 3.279,0.313 0.293,0.161 10 C46 3.349,0.153 3.503,0.313 0.155,0.161 10 *2 5.117,0.153 5.410,0.313 0.293,0.161 10 A38 6.19,0.153 6.345,0.313 0.155,0.161 10 *2 5.814,0.153 6.106,0.313 0.293,0.161 10 A52

HINT:

As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.


a.

Disconnect the A38*1 and C45*1 or A52*2 and C46*2 ECM connectors.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38*1-27 (TC) - Body ground
A52*2-27 (TC) - Body ground
V - Body ground Terminal TC of DLC3 Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground ECM ground Always Below 1 Ω
C45*1-28 (D) - Body ground
C46*2-28 (D) - Body ground
G - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38*1-42 (CLSW) - Body ground
A52*2-42 (CLSW) - Body ground
B - Body ground Clutch signal (M/T) Ignition switch ON
Clutch pedal depressed
Below 1 V
Ignition switch ON
Clutch pedal released
11 to 14 V
A38*1-60 (SFTU) - Body ground
A52*2-60 (SFTU) - Body ground
V - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
Below 1 Ω
Ignition switch ON
Shift lever in "+"
10 kΩ or higher
A38*1-25 (S) - Body ground
A52*2-25 (S) - Body ground
W - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38*1-59 (SFTD) - Body ground
A52*2-59 (SFTD) - Body ground
L - Body ground Park/neutral position switch signal (A/T) Ignition switch ON
Shift lever in S
10 kΩ or higher
Ignition switch ON
Shift lever in "-"
Below 1 Ω
A38*1-36 (STP) - Body ground
A52*2-36 (STP) - Body ground
R - Body ground Stop light signal Ignition switch ON
Brake pedal depressed
11 to 14 V
Ignition switch ON
Brake pedal released
Below 1 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
P - Body ground Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
Below 1 V
Ignition switch ON
Brake pedal released
11 to 14 V
A38*1-40 (CCS) - Body ground
A52*2-40 (CCS) - Body ground
L - Body ground Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch hed on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.

HINT:
·

*1: for LHD

·

*2: for RHD