Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255249 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter self-diagnostic mode. If a malfunction is present, DTCs will be output.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E158854E04
5.923,2.055 6.315,2.253 0.392,0.199 10 ECM 1.502,1.853 1.929,2.037 0.427,0.184 10 DLC3 1.931,0.387 2.174,0.578 0.243,0.191 10 TC 5.804,0.407 6.046,0.598 0.243,0.191 10 TC 1.931,1.23 2.174,1.421 0.243,0.191 10 CG 5.923,1.879 6.380,2.052 0.457,0.173 10 A52*2 5.923,1.705 6.380,1.878 0.457,0.173 10 A38*1 5.351,0.311 5.701,0.457 0.349,0.145 10 27*4 5.351,0.161 5.701,0.306 0.349,0.145 10 16*3 2.283,0.283 2.488,0.470 0.205,0.187 10 13 2.319,1.125 2.468,1.309 0.149,0.184 10 4 1.502,1.697 1.781,1.862 0.279,0.165 10 E22 0.028,2.262 2.152,2.425 2.123,0.163 10 *3: for 1GR-FE, 1UR-FE, 3UR-FE 0.028,2.012 1.103,2.175 1.075,0.163 10 *2: for RHD 0.028,1.762 1.103,1.925 1.075,0.163 10 *1: for LHD 0.028,2.539 1.085,2.702 1.056,0.163 10 *4: for 1VD-FTV

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - ECM AND BODY GROUND)
E349633E01
0.281,0.979 0.635,1.198 0.354,0.219 3.708,1.01 4.063,1.229 0.354,0.219 3.74,1.365 4.094,1.583 0.354,0.219 1.531,1 1.656,0.688 true 1.865,1.542 1.646,1.375 true 6.104,1.021 6.448,0.531 true 6.083,1.125 5.625,0.594 true 0.5,0.125 2,0.354 1.5,0.229 10 false Front view of DLC3 4.552,0.083 6.844,0.667 2.292,0.583 10 false Front view of wire harness connector: (to ECM) 0.333,1.01 0.792,1.208 0.458,0.198 10 false E22 1.573,0.531 2.031,0.729 0.458,0.198 10 false CG 1.813,1.563 2.271,1.76 0.458,0.198 10 false TC 5.333,0.427 5.792,0.625 0.458,0.198 10 false TC*4 0.271,1.802 1.156,1.99 0.885,0.188 10 false *1: for LHD 6.396,0.354 6.854,0.552 0.458,0.198 10 false TC*3 3.781,1.042 4.24,1.24 0.458,0.198 10 false A38 3.792,1.396 4.25,1.594 0.458,0.198 10 false A52 4.094,1.063 4.552,1.26 0.458,0.198 10 false *1 4.115,1.396 4.573,1.594 0.458,0.198 10 false *2 0.281,2.021 1.281,2.208 1,0.188 10 false *2: for RHD 0.302,2.24 2.604,2.479 2.302,0.24 10 false *3: for 1GR-FE, 1UR-FE, 3UR-FE 0.302,2.448 1.531,2.688 1.229,0.24 10 false *4: for 1VD-FTV

a.

Disconnect the A38*1 or A52*2 ECM connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE LHD, 1UR-FE LHD, 3UR-FE LHD
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-16 (TC) Always Below 1 Ω
E22-4 (CG) - Body ground
E22-13 (TC) - Body ground Always 10 kΩ or higher

for 1GR-FE RHD, 1UR-FE RHD
Tester Connection Condition Specified Condition
E22-13 (TC) - A52-16 (TC) Always Below 1 Ω
E22-4 (CG) - Body ground
E22-13 (TC) - Body ground Always 10 kΩ or higher

for 1VD-FTV LHD
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-27 (TC) Always Below 1 Ω
E22-4 (CG) - Body ground
E22-13 (TC) - Body ground Always 10 kΩ or higher

for 1VD-FTV RHD
Tester Connection Condition Specified Condition
E22-13 (TC) - A52-27 (TC) Always Below 1 Ω
E22-4 (CG) - Body ground
E22-13 (TC) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR