Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM (for 1UR-FE)


U165990E01
2.22,0.153 2.513,0.313 0.293,0.161 10 C45 2.583,0.153 2.738,0.313 0.155,0.161 10 *1 5.493,0.153 5.648,0.313 0.155,0.161 10 *1 0.035,2.493 0.766,2.654 0.731,0.161 10 *2: for RHD 0.035,2.23 0.766,2.390 0.731,0.161 10 *1: for LHD 2.986,0.153 3.279,0.313 0.293,0.161 10 C46 3.349,0.153 3.503,0.313 0.155,0.161 10 *2 5.117,0.153 5.410,0.313 0.293,0.161 10 A38 6.19,0.153 6.345,0.313 0.155,0.161 10 *2 5.814,0.153 6.106,0.313 0.293,0.161 10 A52

HINT:

As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.


a.

Disconnect the A38*1 and C45*1 or A52*2 and C46*2 ECM connectors.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38*1-16 (TC) - Body ground
A52*2-16 (TC) - Body ground
V-W - Body ground Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground ECM ground Always Below 1 Ω
C45*1-27 (D) - Body ground
C46*2-27 (D) - Body ground
G - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in D
11 to 14 V
Engine switch on (IG)
Shift lever not in D
Below 1 V
A38*1-38 (SFTU) - Body ground
A52*2-38 (SFTU) - Body ground
Y - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in S
Below 1 Ω
Engine switch on (IG)
Shift lever in +
10 kΩ or higher
A38*1-25 (S) - Body ground
A52*2-25 (S) - Body ground
W - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in S
11 to 14 V
Engine switch on (IG)
Shift lever not in S
Below 1 V
A38*1-27 (SFTD) - Body ground
A52*2-27 (SFTD) - Body ground
L - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in S
10 kΩ or higher
Engine switch on (IG)
Shift lever in -
Below 1 Ω
A38*1-36 (STP) - Body ground
A52*2-36 (STP) - Body ground
R - Body ground Stop light signal Engine switch on (IG)
Brake pedal depressed
11 to 14 V
Engine switch on (IG)
Brake pedal released
Below 1 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
R-W - Body ground Stop light signal (opposite to STP terminal) Engine switch on (IG)
Brake pedal depressed
Below 1 V
Engine switch on (IG)
Brake pedal released
11 to 14 V
A38*1-45 (CCS) - Body ground
A52*2-45 (CCS) - Body ground
L - Body ground Cruise control main switch signal Engine switch on (IG)
Main switch off
1 MΩ or higher
Engine switch on (IG)
CANCEL switch held on
1510 to 1570 Ω
Engine switch on (IG)
-SET switch held on
620 to 640 Ω
Engine switch on (IG)
+RES switch held on
235 to 245 Ω
Engine switch on (IG)
Main switch on
Below 2.5 Ω
A38*1-37 (CCHG) - Body ground
A52*2-37 (CCHG) - Body ground
P-B - Body ground Distance control switch signal Engine switch on (IG)
Main switch on
MODE switch held on
Below 1 V
Engine switch on (IG)
Main switch on
MODE switch off
11 to 14 V

*1: for LHD

*2: for RHD


If the result is not as specified, there may be a malfunction on the wire harness side.



CHECK ECM (for 3UR-FE)


U165992E02
2.469,0.167 2.76,0.323 0.292,0.156 10 false C45 5.615,0.167 5.906,0.323 0.292,0.156 10 false A38

HINT:

As the ECM connector is a waterproof connector, it is not possible to check the voltage of each terminal or check the waveform with an oscilloscope while the ECM is installed in the vehicle.


a.

Disconnect the A38 and C45 ECM connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-16 (TC) - Body ground V-W - Body ground Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
C45-81 (E1) - Body ground W-B - Body ground ECM ground Always Below 1 Ω
C45-27 (D) - Body ground G - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in D
11 to 14 V
Engine switch on (IG)
Shift lever not in D
Below 1 V
A38-38 (SFTU) - Body ground Y - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in S
Below 1 Ω
Engine switch on (IG)
Shift lever in +
10 kΩ or higher
A38-25 (S) - Body ground W - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in S
11 to 14 V
Engine switch on (IG)
Shift lever not in S
Below 1 V
A38-27 (SFTD) - Body ground L - Body ground Park/neutral position switch signal Engine switch on (IG)
Shift lever in S
10 kΩ or higher
Engine switch on (IG)
Shift lever in -
Below 1 Ω
A38-36 (STP) - Body ground R - Body ground Stop light signal Engine switch on (IG)
Brake pedal depressed
11 to 14 V
Engine switch on (IG)
Brake pedal released
Below 1 V
A38-35 (ST1-) - Body ground R-W - Body ground Stop light signal (opposite to STP terminal) Engine switch on (IG)
Brake pedal depressed
Below 1 V
Engine switch on (IG)
Brake pedal released
11 to 14 V
A38-45 (CCS) - Body ground L - Body ground Cruise control main switch signal Engine switch on (IG)
Main switch off
1 MΩ or higher
Engine switch on (IG)
CANCEL switch held on
1510 to 1570 Ω
Engine switch on (IG)
-SET switch held on
620 to 640 Ω
Engine switch on (IG)
+RES switch held on
235 to 245 Ω
Engine switch on (IG)
Main switch on
Below 2.5 Ω
A38-37 (CCHG) - Body ground P-B - Body ground Distance control switch signal Engine switch on (IG)
Main switch on
MODE switch held on
Below 1 V
Engine switch on (IG)
Main switch on
MODE switch off
11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.



CHECK DISTANCE CONTROL ECU


U165810E02
3.458,0.302 3.802,0.448 0.344,0.146 10 false E108

a.

Disconnect the E108 distance control ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E108-1 (B) - Body ground R - Body ground Distance control ECU power source line Engine switch on (IG) 11 to 14 V
E108-3 (WASH) - Body ground L - Body ground Windshield wiper switch signal Engine switch on (IG)
Windshield wiper switch on
11 to 14 V
Engine switch on (IG)
Windshield wiper switch off
Below 1 V
E108-12 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω
E108-13 (IGB) - Body ground R - Body ground Engine switch on (IG) signal Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
E108-16 (MODE) - Body ground W - Body ground Distance control switch signal Engine switch on (IG)
Distance control switch on
Below 1 V
Engine switch on (IG)
Distance control switch off
11 to 14 V
E108-22 (LRDD) - E108-10 (SGND) B - R Millimeter wave radar sensor input signal Engine switch on (IG) Pulse generation
(See waveform 1)
E108-23 (LRRD) - E108-10 (SGND) W - R Millimeter wave radar sensor output signal Engine switch on (IG) Pulse generation
(See waveform 2)

If the result is not as specified, there may be a malfunction on the wire harness side.


c.
E109730E17
2.927,1.177 3.354,1.375 0.427,0.198 10 false SGND 1.406,1.906 1.99,2.104 0.583,0.198 10 false 10 msec. 0.354,0.198 0.594,0.396 0.24,0.198 10 false 2 V

Using an oscilloscope, check waveform 1.

Item Content
Terminal No. (Symbol) E108-22 (LRDD) - E108-10 (SGND)
Tool Setting 2 V/DIV., 10 msec./DIV.
Condition Engine switch on (IG)


d.
E109731E17
2.927,1.177 3.354,1.375 0.427,0.198 10 false SGND 1.448,1.885 1.958,2.083 0.51,0.198 10 false 5 msec. 0.365,0.229 0.604,0.427 0.24,0.198 10 false 2 V

Using an oscilloscope, check waveform 2.

Item Content
Terminal No. (Symbol) E108-23 (LRRD) - E108-10 (SGND)
Tool Setting 2 V/DIV., 5 msec./DIV.
Condition Engine switch on (IG)



CHECK MILLIMETER WAVE RADAR SENSOR


U166020E02
3.313,0.271 3.604,0.417 0.292,0.146 10 false A56

a.

Disconnect the A56 millimeter wave radar sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A56-3 (LRDD) - A56-2 (SGND) B - R Millimeter wave radar sensor output signal Engine switch on (IG) Pulse generation
(See waveform 3)
A56-4 (LRRD) - A56-2 (SGND) W - R Millimeter wave radar sensor input signal Engine switch on (IG) Pulse generation
(See waveform 4)
A56-5 (IGB) - A56-2 (SGND) R - R Engine switch on (IG) signal Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.
E109730E17
2.927,1.177 3.354,1.375 0.427,0.198 10 false SGND 1.406,1.906 1.99,2.104 0.583,0.198 10 false 10 msec. 0.354,0.198 0.594,0.396 0.24,0.198 10 false 2 V

Using an oscilloscope, check waveform 3.

Item Content
Terminal No. (Symbol) A56-3 (LRDD) - A56-2 (SGND)
Tool Setting 2 V/DIV., 10 msec./DIV.
Condition Engine switch on (IG)


d.
E109731E17
2.927,1.177 3.354,1.375 0.427,0.198 10 false SGND 1.448,1.885 1.958,2.083 0.51,0.198 10 false 5 msec. 0.365,0.229 0.604,0.427 0.24,0.198 10 false 2 V

Using an oscilloscope, check waveform 4.

Item Content
Terminal No. (Symbol) A56-4 (LRRD) - A56-2 (SGND)
Tool Setting 2 V/DIV., 5 msec./DIV.
Condition Engine switch on (IG)