Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM (for 3UR-FE)


U165998E02
2.438,0.167 2.729,0.323 0.292,0.156 10 false C45 5.458,0.167 5.75,0.323 0.292,0.156 10 false A38

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C45-81 (E1) - Body ground W-B - Body ground ECM ground Always Below 1 Ω
C45-49 (D) - Body ground P - Body ground D shift position signal Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38-39 (SFTU) - Body ground V - Body ground Up-shift switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever in +
Below 1 V
A38-27 (S) - Body ground W - Body ground S shift position switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38-47 (SFTD) - Body ground L - Body ground Down-shift switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever in -
Below 1 V
A38-7 (STP) - Body ground R - Body ground Stop light signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A38-8 (ST1-) - Body ground P - Body ground Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
0 to 1.5 V
Ignition switch ON
Brake pedal released
7.5 to 14 V
A38-60 (CCS) - A38-59 (ECCS) L - BR Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch held on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω


CHECK ECM (for 1UR-FE)


U165999E01
2.22,0.153 2.513,0.313 0.293,0.161 10 C45 2.583,0.153 2.738,0.313 0.155,0.161 10 *1 5.493,0.153 5.648,0.313 0.155,0.161 10 *1 0.035,2.493 0.766,2.654 0.731,0.161 10 *2: for RHD 0.035,2.23 0.766,2.390 0.731,0.161 10 *1: for LHD 2.986,0.153 3.279,0.313 0.293,0.161 10 C46 3.349,0.153 3.503,0.313 0.155,0.161 10 *2 5.117,0.153 5.410,0.313 0.293,0.161 10 A38 6.19,0.153 6.345,0.313 0.155,0.161 10 *2 5.814,0.153 6.106,0.313 0.293,0.161 10 A52

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground ECM ground Always Below 1 Ω
C45*1-27 (D) - Body ground
C46*2-27 (D) - Body ground
Y - Body ground D shift position signal Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38*1-38 (SFTU) - Body ground
A52*2-38 (SFTU) - Body ground
V - Body ground Up-shift switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever in "+"
Below 1 V
A38*1-25 (S) - Body ground
A52*2-25 (S) - Body ground
W - Body ground S shift position switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38*1-27 (SFTD) - Body ground
A52*2-27 (SFTD) - Body ground
L - Body ground Down-shift switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever in "-"
Below 1 V
A38*1-36 (STP) - Body ground
A52*2-36 (STP) - Body ground
R - Body ground Stop light signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
P - Body ground Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
0 to 1.5 V
Ignition switch ON
Brake pedal released
7.5 to 14 V
A38*1-45 (CCS) - Body ground
A52*2-45 (CCS) - Body ground
L - Body ground Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch held on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω

*1: for LHD

*2: for RHD



CHECK ECM (for 1VD-FTV)


U166000E01
2.22,0.153 2.513,0.313 0.293,0.161 10 C45 2.583,0.153 2.738,0.313 0.155,0.161 10 *1 5.493,0.153 5.648,0.313 0.155,0.161 10 *1 0.035,2.493 0.766,2.654 0.731,0.161 10 *2: for RHD 0.035,2.23 0.766,2.390 0.731,0.161 10 *1: for LHD 2.986,0.153 3.279,0.313 0.293,0.161 10 C46 3.349,0.153 3.503,0.313 0.155,0.161 10 *2 5.117,0.153 5.410,0.313 0.293,0.161 10 A38 6.19,0.153 6.345,0.313 0.155,0.161 10 *2 5.814,0.153 6.106,0.313 0.293,0.161 10 A52

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of the checks should be compared with the standard normal voltage for that pair of terminals, which is displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C45*1-81 (E1) - Body ground
C46*2-81 (E1) - Body ground
BR - Body ground ECM ground Always Below 1 Ω
C45*1-28 (D) - Body ground
C46*2-28 (D) - Body ground
P - Body ground D shift position signal Ignition switch ON
Shift lever in D
11 to 14 V
Ignition switch ON
Shift lever not in D
Below 1 V
A38*1-38 (SFTU) - Body ground
A52*2-38 (SFTU) - Body ground
V - Body ground Up-shift switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever in "+"
Below 1 V
A38*1-25 (S) - Body ground
A52*2-25 (S) - Body ground
W - Body ground S shift position switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever not in S
Below 1 V
A38*1-37 (SFTD) - Body ground
A52*2-37 (SFTD) - Body ground
L - Body ground Down-shift switch signal Ignition switch ON
Shift lever in S
11 to 14 V
Ignition switch ON
Shift lever in "-"
Below 1 V
A38*1-13 (STP) - Body ground
A52*2-13 (STP) - Body ground
R - Body ground Stop light signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A38*1-35 (ST1-) - Body ground
A52*2-35 (ST1-) - Body ground
P - Body ground Stop light signal (opposite to STP terminal) Ignition switch ON
Brake pedal depressed
0 to 1.5 V
Ignition switch ON
Brake pedal released
7.5 to 14 V
A38*1-40 (CCS) - Body ground
A52*2-40 (CCS) - Body ground
L - Body ground Cruise control main switch signal Ignition switch ON
Main switch off
1 MΩ or higher
Ignition switch ON
CANCEL switch held on
1510 to 1570 Ω
Ignition switch ON
-SET switch hed on
620 to 640 Ω
Ignition switch ON
+RES switch held on
235 to 245 Ω
Ignition switch ON
Main switch on
Below 2.5 Ω

*1: for LHD

*2: for RHD



CHECK DRIVING SUPPORT ECU ASSEMBLY


U166507E02
3.354,0.156 3.729,0.333 0.375,0.177 10 false E164

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E164-3 (BZ) - E164-28 (GND) L - BR Pre-collision city buzzer output Engine switch on (IG), buzzer not sounding 11 to 14 V
E164-7 (B) - E164-28 (GND) P - BR Power source Engine switch on (IG) 11 to 14 V
E164-8 (CA1P) - E164-28 (GND) W - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
E164-9 (CA1N) - E164-28 (GND) P - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)
E164-10 (CA2H) - E164-28 (GND) L - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
E164-11 (CA2L) - E164-28 (GND) B - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)
E164-23 (SPSW) - E164-28 (GND) W - BR Steering pad switch signal (Distance control switch signal) Engine switch on (IG), Distance control switch on Below 1 Ω
E164-23 (SPSW) - E164-28 (GND) W - BR Steering pad switch signal (Distance control switch signal) Engine switch on (IG), Distance control switch off 4.75 to 5.25 V
E164-28 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

a.
E349639E01
2.656,0.313 3.208,0.479 0.552,0.167 10 false 1 V/DIV. 1.302,1.76 2.385,1.99 1.083,0.229 10 false 10 μsec./DIV. 2.833,1.333 3.281,1.51 0.448,0.177 10 false GND

WAVEFORM 1

i.

CAN communication signal

Item Content
Terminal Name Between E164-8 (CA1P) and E164-28 (GND)
Between E164-10 (CA2H) and E164-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E349640E01
2.667,0.365 3.365,0.573 0.698,0.208 10 false 1 V/DIV. 1.333,1.833 2.563,2.031 1.229,0.198 10 false 10 μsec./DIV. 2.875,1.354 3.24,1.542 0.365,0.188 10 false GND

WAVEFORM 2

i.

CAN communication signal

Item Content
Terminal Name Between E164-9 (CA1N) and E164-28 (GND)
Between E164-11 (CA2L) and E164-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR


U166509E02
2.406,0.854 2.677,1.01 0.271,0.156 10 false A72

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A72-1 (SGND) - Body ground BR - Body ground Ground Always Below 1 Ω
A72-2 (CA2L) - A72-1 (SGND) B - BR CAN communication signal Engine switch on (IG) Pulse generation
(see waveform 2)
A72-3 (CA2H) - A72-1 (SGND) L - BR CAN communication signal Engine switch on (IG) Pulse generation
(see waveform 1)
A72-5 (CA1P) - A72-1 (SGND) B - BR CAN communication signal Engine switch on (IG) Pulse generation
(see waveform 1)
A72-6 (CA1N) - A72-1 (SGND) P - BR CAN communication signal Engine switch on (IG) Pulse generation
(see waveform 2)
A72-8 (IGB) - A72-1 (SGND) G - BR Power source Engine switch on (IG) 11 to 14 V

a.
E349639E01
2.656,0.313 3.208,0.479 0.552,0.167 10 false 1 V/DIV. 1.302,1.76 2.385,1.99 1.083,0.229 10 false 10 μsec./DIV. 2.833,1.333 3.281,1.51 0.448,0.177 10 false GND

WAVEFORM 1

i.

CAN communication signal

Item Content
Terminal Name Between A72-3 (CA2H) and A72-1 (SGND)
Between A72-5 (CA1P) and A72-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E349640E01
2.667,0.365 3.365,0.573 0.698,0.208 10 false 1 V/DIV. 1.333,1.833 2.563,2.031 1.229,0.198 10 false 10 μsec./DIV. 2.875,1.354 3.24,1.542 0.365,0.188 10 false GND

WAVEFORM 2

i.

CAN communication signal

Item Content
Terminal Name Between A72-2 (CA2L) and A72-1 (SGND)
Between A72-6 (CA1N) and A72-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.