Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter self-diagnostic mode. If a malfunction is present, DTCs will be output.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E158854E05
5.927,2.073 6.323,2.271 0.396,0.198 10 false ECM 1.5,1.885 1.927,2.073 0.427,0.188 10 false DLC3 1.969,0.417 2.208,0.604 0.24,0.188 10 false TC 5.802,0.406 6.042,0.594 0.24,0.188 10 false TC 1.927,1.271 2.167,1.458 0.24,0.188 10 false CG 5.927,1.875 6.385,2.052 0.458,0.177 10 false A53*2 5.927,1.677 6.385,1.854 0.458,0.177 10 false A38*1 5.469,0.281 5.698,0.427 0.229,0.146 10 false 16 2.25,0.271 2.458,0.458 0.208,0.188 10 false 13 2.281,1.104 2.427,1.292 0.146,0.188 10 false 4 1.5,1.698 1.781,1.865 0.281,0.167 10 false E22 0.094,2.521 1.167,2.792 1.073,0.271 10 false *2: for RHD 0.073,2.229 1.146,2.5 1.073,0.271 10 false *1: for LHD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - ECM AND BODY GROUND)
a.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for LHD

*2: for RHD


E349661E01
0.438,1.583 0.74,1.802 0.302,0.219 3.594,1.51 3.896,1.729 0.302,0.219 3.604,1.792 3.906,2.01 0.302,0.219 1.677,1.594 2.094,1.177 true 2.052,2.323 1.771,1.979 true 5.958,1.656 6.167,1.042 true 0.458,1.615 0.917,1.813 0.458,0.198 10 false E22 2.146,1.01 2.604,1.208 0.458,0.198 10 false CG 4.292,0.083 6.667,0.51 2.375,0.427 10 false Front view of wire harness connector: (to ECM) 3.958,1.552 4.417,1.75 0.458,0.198 10 false *1 3.99,1.823 4.448,2.021 0.458,0.198 10 false *2 3.646,1.802 4.104,2 0.458,0.198 10 false A52 2.052,2.365 2.51,2.563 0.458,0.198 10 false TC 0.979,0.198 2.594,0.448 1.615,0.25 10 false Front view of DLC3 3.75,2.99 4.781,3.219 1.031,0.229 10 false *1: for LHD 3.625,1.552 4.083,1.75 0.458,0.198 10 false A38 6.188,0.823 6.646,1.021 0.458,0.198 10 false TC 3.771,3.229 4.583,3.469 0.813,0.24 10 false *2: for RHD


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-16 (TC) Always Below 1 Ω
E22-4 (CG) - Body ground
E22-13 (TC) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E22-13 (TC) - A52-16 (TC) Always Below 1 Ω
E22-4 (CG) - Body ground
E22-13 (TC) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR