Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM D

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  ROAD TEST  


HINT:

The dynamic radar cruise control system has 2 cruise control modes: the constant speed control mode and vehicle-to-vehicle distance control mode.

·

The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.

·

Operation of the constant speed control mode is the same as the cruise control system.



INSPECT SET SWITCH


E349634

a.

Turn the cruise control main switch on.


b.

Drive at the desired speed (50 km/h [30 mph] or higher).


c.

Push the cruise control main switch to -SET (COAST/SET).


d.

Check that the vehicle cruises at the desired speed.



INSPECT "+" SWITCH


E349635

a.

Turn the cruise control main switch on.


b.

Drive at the desired speed (50 km/h [30 mph] or higher).


c.

Push the cruise control main switch to -SET (COAST/SET).


d.

Check that vehicle speed increases while the cruise control main switch is pushed to +RES (ACCELERATION/RESUME), and that the vehicle cruises at the set speed when released.


e.

Vehicle-to-vehicle distance control mode:

Momentarily push the cruise control main switch to +RES (ACCELERATION/RESUME), and then immediately release it. Check that the driving and the stored vehicle speed increase by 5 km/h or 5 mph (Tap-up function).

HINT:

Pushing the cruise control main switch to +RES while following a vehicle in front with the vehicle-to-vehicle distance control mode on does not increase the actual vehicle speed, but changes only the stored vehicle speed.



f.

Constant speed control mode:

Momentarily push the control main switch to +RES (ACCELERATION/RESUME), and then immediately release it. Check that the vehicle speed increases by approximately 1.6 km/h (1.0 mph) (Tap-up function).



INSPECT "-" SWITCH


E349634

a.

Turn the cruise control main switch on.


b.

Drive at the desired speed (50 km/h [30 mph] or higher).


c.

Push the cruise control main switch to -SET (COAST/SET).


d.

Check that vehicle speed decreases while the cruise control main switch is pushed to -SET (COAST/SET), and the vehicle cruises at the set speed when released.


e.

Vehicle-to-vehicle distance control mode:

Momentarily push the cruise control main switch to -SET (COAST/SET), and then immediately release it. Check that the driving and the stored vehicle speed decrease by 5 km/h or 5 mph (Tap-down function).


f.

Constant speed control mode:

Momentarily push the cruise control main switch to -SET (COAST/SET), and then immediately release it. Check that the vehicle speed decreases by approximately 1.6 km/h (1.0 mph) (Tap-down function).


g.

Check that the set speed is displayed on the multi-information display in the combination meter assembly and that the "SET" indicator light illuminates.



INSPECT CANCEL SWITCH


E349636

a.

Turn the cruise control main switch on.


b.

Drive at the desired speed (50 km/h [30 mph] or higher).


c.

Push the cruise control main switch to -SET (COAST/SET).


d.

When performing one of the following, check that the cruise control system is canceled.

·

Depressing the brake pedal.

·

Moving the shift lever from D to N.

·

With the shift lever in S, selecting the S1, S2 or S3 range.

·

Turning the cruise control main switch off (the stored vehicle speed in the ECM is not maintained).

·

Pulling the cruise control main switch to CANCEL.

·

Driving the vehicle while the VSC system is operating.




INSPECT RES (RESUME) SWITCH


E349635

a.

Turn the cruise control main switch on.


b.

Drive at the desired speed (50 km/h [30 mph] or higher).


c.

Push the cruise control main switch to -SET (COAST/SET).


d.

Cancel the cruise control system by performing any of the operations below.

·

Depressing the brake pedal.

·

Moving the shift lever from D to N.

·

With the shift lever in S, selecting the S1, S2 or S3 range.

·

Pulling the cruise control switch to CANCEL.

·

Driving the vehicle while the VSC system is operating.



e.

After the cruise control main switch is pushed to +RES (ACCELERATION/RESUME) at a driving speed of more than 40 km/h (25 mph), check that the vehicle restores the speed before the cancellation and the cruise control "SET" indicator light illuminates.