Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on dynamic radar cruise control system operation, the driving support ECU assembly provides warnings to the driver by sounding the pre-crash safety city buzzer.

DTC C1A4A is stored when a malfunction is detected in the pre-crash safety city buzzer circuit.

DTC No. DTC Detection Condition Trouble Area
C1A4A While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the driving support ECU assembly detects a malfunction in the pre-crash safety city buzzer circuit for 0.4 seconds or more.
·

Pre-crash safety city buzzer

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

B403796E80
0.552,0.698 1.896,0.958 1.344,0.26 10 false from IG Circuit 2.052,0.854 3.396,1.115 1.344,0.26 10 false ECU-IG NO. 6 5.073,2.24 7.042,2.542 1.969,0.302 10 false Driving Support ECU Assembly 3.292,1.188 5.25,1.49 1.958,0.302 10 false Pre-crash Safety City Buzzer 3.302,1.021 3.76,1.219 0.458,0.198 10 false E5 3.563,0.698 4.021,0.896 0.458,0.198 10 false IG1 4.25,0.698 4.708,0.896 0.458,0.198 10 false BZ 5.521,0.708 5.979,0.906 0.458,0.198 10 false BZ 5.365,0.594 5.823,0.792 0.458,0.198 10 false 3 4.49,0.583 4.948,0.781 0.458,0.198 10 false 1 3.406,0.594 3.865,0.792 0.458,0.198 10 false 2 5.104,2.052 5.563,2.25 0.458,0.198 10 false E164

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (RADAR CRUISE APPROACH ALARM BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Pre-crash safety city buzzer (approach sound)
Tester Display Test Part Control Range Diagnostic Note
Radar Cruise Approach Alarm Buzzer Pre-crash safety city buzzer ON or OFF Buzzer can be heard

OK:

Pre-crash safety city buzzer sounds.




OK

2.CHECK FOR DTCs (RADAR CRUISE2)

NG

3.CHECK TERMINAL VOLTAGE
2.CHECK FOR DTCs (RADAR CRUISE2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.




e.

Enter the following menus: Powertrain / Radar Cruise2 / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC C1A4A is output A
DTC C1A4A is not output B




A

REPLACE DRIVING SUPPORT ECU ASSEMBLY

B

3.CHECK TERMINAL VOLTAGE
a.

Disconnect the E5 pre-crash safety city buzzer connector.


b.
U164299E01
2.441,1.806 2.798,1.969 0.357,0.163 10 IG1 1.972,1.547 2.395,1.875 false 0.515,1.08 0.713,1.240 0.199,0.159 10 E5 0.126,0.099 0.314,0.282 0.188,0.184 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E5-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
E5-2 (IG1) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Pre-crash Safety City Buzzer)



OK

4.INSPECT PRE-COLLISION CITY BUZZER (UNIT INSPECTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PRE-COLLISION CITY BUZZER (UNIT INSPECTION)
a.

Remove the pre-crash safety city buzzer (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL).


b.

Inspect the pre-crash safety city buzzer (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>INSPECTION).

Result:
Result Proceed to
Pre-crash safety city buzzer is normal. A
Pre-crash safety city buzzer is abnormal. B




A

5.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - DRIVING SUPPORT ECU ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the E5 pre-crash safety city buzzer connector.


b.

Disconnect the E164 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E5-1 (BZ) - E164-3 (BZ) Always Below 1 Ω
E5-1 (BZ) or E164-3 (BZ) - Body ground Always 10 kΩ or higher




OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR