Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255254 ROAD SIGN ASSIST SYSTEM U

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


U166390E02
2.083,0.792 2.365,0.938 0.281,0.146 10 false R20

a.

Disconnect the R20 forward recognition camera connector.

NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the R20 forward recognition camera connector.




b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R20-7 (IGB) - Body ground B - Body ground Power source Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
R20-10 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the R20 forward recognition camera connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R20-5 (CA1P) - R20-10 (GND) G - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
R20-11 (CA1N) - R20-10 (GND) B - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)
R20-6 (CANH) - R20-10 (GND) R - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 1)
R20-12 (CANL) - R20-10 (GND) P - BR CAN communication signal Engine switch on (IG) Pulse generation
(See waveform 2)


e.
E349639E01
2.656,0.313 3.208,0.479 0.552,0.167 10 false 1 V/DIV. 1.302,1.76 2.385,1.99 1.083,0.229 10 false 10 μsec./DIV. 2.833,1.333 3.281,1.51 0.448,0.177 10 false GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

R20-5 (CA1P) - R20-10 (GND)

·

R20-6 (CANH) - R20-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




f.
E349640E01
2.667,0.365 3.365,0.573 0.698,0.208 10 false 1 V/DIV. 1.333,1.833 2.563,2.031 1.229,0.198 10 false 10 μsec./DIV. 2.875,1.354 3.24,1.542 0.365,0.188 10 false GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

R20-11 (CA1N) - R20-10 (GND)

·

R20-12 (CANL) - R20-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.