These DTCs are output when a communication malfunction occurs between the sensors and ECUs.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| U0100 | While the vehicle is being driven at 1 km/h (1 mph) or more, a communication error between the ECM and the forward recognition camera is detected for approximately 5 seconds or more. | ·
CAN communication system ·
ECM ·
Forward recognition camera |
| U0101 | While the vehicle is being driven at 1 km/h (1 mph) or more, a communication error between the TCM and the forward recognition camera is detected for approximately 5 seconds or more. | ·
CAN communication system ·
TCM ·
Forward recognition camera |
| U0123 | While the vehicle is being driven at 1 km/h (1 mph) or more, a communication error between the yaw rate sensor (airbag sensor assembly) and the forward recognition camera is detected for approximately 5 seconds or more. | ·
CAN communication system ·
Yaw rate sensor (airbag sensor assembly) ·
Forward recognition camera |
| U0126 | 2 seconds after the engine switch is turned on (IG), a communication error between the steering sensor and the forward recognition camera is detected for approximately 5 seconds or more. | ·
CAN communication system ·
Steering sensor ·
Forward recognition camera |
| U0129 | 2 seconds after the engine switch is turned on (IG), a communication error between the skid control ECU (master cylinder solenoid) and the forward recognition camera is detected for approximately 5 seconds or more. | ·
CAN communication system ·
Skid control ECU (master cylinder solenoid) ·
Forward recognition camera |
| U0142 | 2 seconds after the engine switch is turned on (IG), a communication error between the main body ECU (multiplex network body ECU) and the forward recognition camera is detected for approximately 5 seconds or more. | ·
CAN communication system ·
Main body ECU (multiplex network body ECU) ·
Forward recognition camera |
| U0155 | While the engine switch is on (IG), a communication error between the combination meter assembly and the forward recognition camera is detected for approximately 50 seconds or more. | ·
CAN communication system ·
Combination meter assembly ·
Forward recognition camera |
| U0235 | 2 seconds after the engine switch is turned on (IG), a communication error between the driving support ECU assembly and the forward recognition camera is detected for approximately 5 seconds. | ·
CAN communication system ·
Millimeter wave radar sensor assembly ·
Forward recognition camera |
| U1104 | 2 seconds after the engine switch is turned on (IG), a communication error between the driving support ECU assembly and the forward recognition camera is detected for approximately 5 seconds. | ·
CAN communication system ·
Driving support ECU assembly ·
Forward recognition camera |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Turn the engine switch on (IG) and wait 50 seconds or more.
Drive the vehicle at 1km/h (1 mph) or more for 5 second or more.
Check the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC U0100, U0101, U0123, U0126, U0129, U0142, U0155, U0235 and U1104 are not output | A |
| DTC U0100, U0101, U0123, U0126, U0129, U0142, U0155, U0235 or U1104 is output (for LHD) | B |
| DTC U0100, U0101, U0123, U0126, U0129, U0142, U0155, U0235 or U1104 is output (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C