Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255255 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1A48  G Sensor  


DESCRIPTION

The forward recognition camera receives G sensor signals from the airbag sensor assembly via CAN communication.

If the forward recognition camera receives a G sensor malfunction signal from the airbag sensor assembly, DTC C1A48 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A48 2 seconds after the engine switch is turned on (IG), a signal from the yaw rate sensor indicating that there is a G sensor malfunction is detected by the forward recognition camera for 5 seconds or more.
·

Vehicle stability control system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

If the airbag sensor assembly (yaw rate and acceleration sensor) is malfunctioning, DTCs for the vehicle stability control system will be stored. Troubleshoot the vehicle stability control system first.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.



Result
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B


A

2.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)

B

2.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result
Result Proceed to
DTC C1A48 is output A
DTC C1A48 is not output B


A

3.REPLACE FORWARD RECOGNITION CAMERA

B

3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL).


b.

Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



NEXT

4.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)
4.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result
Result Proceed to
DTC C1A48 is output A
DTC C1A48 is not output B


A

REPLACE AIRBAG SENSOR ASSEMBLY (YAW RATE AND ACCELERATION SENSOR)

B

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)