Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255255 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AAC  Vehicle Information Unmatched  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the vehicle information received from the ECM. If the vehicle information stored in the forward recognition camera is different from that stored in the ECM, DTC C1AAC is stored.

DTC No. DTC Detection Condition Trouble Area
C1AAC 2 seconds after the engine switch is turned on (IG), the vehicle information received from the ECM and that stored in the forward recognition camera do not match.
·

CAN communication system

·

Forward recognition camera

·

ECM



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



HINT:

This DTC is stored when the vehicle information stored in the forward recognition camera and that stored in the ECM do not match. If the forward recognition camera or ECM has been replaced, check if a forward recognition camera or ECM from another vehicle was used.


PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION DTC OUTPUT)
HINT:

The forward recognition camera communicates with the ECM via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



Result
Result Proceed to
DTC U0100 is not output A
DTC U0100 is output (for LHD) B
DTC U0100 is output (for RHD) C


A

2.READ VALUE USING GTS

B

C

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Data List.


Front Recognition Camera
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Information (2WD/4WD) Vehicle information (drivetrain) stored in forward recognition camera/
2WD, 4WD or Unknown
2WD: for 2WD
4WD: for 4WD
Unknown: Vehicle information not confirmed
-
Vehicle Information (Conv/HV) Vehicle information (conventional/ hybrid) stored in forward recognition camera/
Conv, HV or Unknown
Conv: Conventional
HV: Hybrid vehicle
Unknown: Vehicle information not confirmed
-

HINT:
·

The vehicle information stored in the forward recognition camera is displayed on the Data List.

·

If the vehicle information stored in the forward recognition camera is different from the actual vehicle specifications, the vehicle information stored in the forward recognition camera may be incorrect. Check for DTCs and replace the forward recognition camera if necessary.

·

If the vehicle information stored in the forward recognition camera matches the actual vehicle specifications, the installed ECM is incompatible. Replace the ECM with a correct one.



Result
Result Proceed to
Vehicle information stored in forward recognition camera and actual vehicle specifications do not match A
Vehicle information stored in forward recognition camera and actual vehicle specifications match (for 1UR-FE) B
Vehicle information stored in forward recognition camera and actual vehicle specifications match (for 3UR-FE) C
Vehicle information stored in forward recognition camera and actual vehicle specifications match (for 1VD-FTV) D


A

3.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)

B

C

D

3.CHECK DTC OUTPUT (LANE DEPARTURE ALERT SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 2 seconds or more.





Result
Result Proceed to
DTC C1AAC is output A
DTC C1AAC is not output B


A

REPLACE FORWARD RECOGNITION CAMERA

B