Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION FLUID › 2015.08–2019.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255259 AUTOMATIC TRANSMISSION FLUID N

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:
·

This transmission requires Toyota Genuine ATF WS.

·

After servicing the transmission, you must follow the ATF adjustment procedure.

·

Maintain the vehicle in a horizontal position while adjusting the fluid level.



PROCEDURE

Hide 1. PRELIMINARY PROCEDURES (w/ ATF Warmer)

a.

Using compressed air or equivalent, blow dust off the thermostat cap to clean it.


b.
C193546E02
1.735,2.378 1.908,2.525 0.173,0.147 10 *3 2.854,3.518 3.026,3.675 0.172,0.157 10 *4 1.787,4.003 1.964,4.155 0.177,0.152 10 *5 1.215,2.738 1.388,2.887 0.172,0.149 10 *2 0.709,3.877 0.888,4.032 0.178,0.155 10 *1 0.817,3.467 0.817,3.862 false 1.894,3.681 1.894,3.989 false 1.947,3.149 2.822,3.601 2.822,3.601 1.94,3.535 false 2.439,3.279 1.94,2.519 false 1.776,3.044 1.415,2.829 false

Using a screwdriver, push in the shaft of the thermostat.

Text in Illustration
*1 Screwdriver
*2 Cap
*3 Shaft
*4 Step
*5 Pin

HINT:
·

Pushed amount: 5.5 to 7.0 mm (0.217 to 0.276 in.)

·

Push in the shaft until the screwdriver contacts the step inside the cap.




c.

With the shaft of the thermostat pressed, insert a pin into a hole on the side of the thermostat cap. Insert the pin until it passes through the hole on the other side of the thermostat cap to fix the shaft in place.

HINT:

Pin diameter: 1.0 to 1.8 mm (0.0394 to 0.0709 in.)



Hide 2.BEFORE FILLING TRANSMISSION

C175571E03
1.698,3.573 1.469,4.146 1.469,4.146 1.354,4.146 false 1.833,1.698 1.542,2.448 1.542,2.448 1.667,2.448 false 2.375,2.01 2.292,2.219 2.292,2.219 2.469,2.219 false 1.125,4.063 1.375,4.26 0.25,0.198 10 true *3 2.573,2.135 2.823,2.344 0.25,0.208 10 false *1 1.74,2.354 1.958,2.542 0.219,0.188 10 false *2

·

This transmission requires Toyota Genuine ATF WS transmission fluid.

·

After servicing the transmission, you must refill the transmission with the correct amount of fluid.

·

Keep the vehicle level while adjusting the fluid level.

·

Proceed to the "Transmission Pan Fill" procedures if you replaced the entire transmission, transmission pan, drain plug, valve body and/or torque converter.

·

Proceed to the "Transmission Fill" procedures after removing the refill plug if you replaced the transmission hose and/or output shaft oil seal.

Text in Illustration
*1 Refill Plug
*2 Refill Hole
*3 Overflow Plug


Hide 3. TRANSMISSION PAN FILL

C161094E06
0.625,0.771 0.406,0.771 0.406,0.771 0.406,1.104 false 1.823,0.813 2.813,0.813 false 0.323,1.146 0.563,1.365 0.24,0.219 10 false *a 2.875,0.729 3.094,0.938 0.219,0.208 10 false *1

a.

Remove the refill plug and overflow plug.


b.

Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.


c.

Reinstall the overflow plug.

Text in Illustration
*1 Overflow Tube
*a Specified Fluid Level


Hide 4. TRANSMISSION FILL

a.

Fill the transmission with the amount of fluid listed in the table below.

Standard Capacity:
Repair Fill Amount
Transmission pan and drain plug removal 2.1 liters (2.2 US qts, 1.9 Imp. qts)
Transmission valve body removal 4.7 liters (5.0 US qts, 4.1 Imp. qts)
Torque converter removal 6.1 liters (6.4 US qts, 5.4 Imp. qts)



b.

Reinstall the refill plug to prevent the fluid from splashing.

HINT:

If you cannot add the listed amount of fluid, do the following:


i.

Install the refill plug.


ii.

Allow the engine to idle with the air conditioning OFF.


iii.

Move the shift lever through the entire gear range to circulate fluid.


iv.

Wait for 30 seconds with the engine idling.


v.

Stop the engine.


vi.

Remove the refill plug and add fluid.


vii.

Reinstall the refill plug.



Hide 5.ADJUST FLUID TEMPERATURE

NOTICE:

The fluid temperature can be confirmed by checking the indicator light in the meter or by using the GTS. When using the GTS, it is necessary to change to temperature detection mode in order to idle the vehicle appropriately.


a.

When using the GTS:

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.


v.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.


vi.

for 1VD-FTV:

Check the ATF temperature.

NOTICE:
·

The ATF temperature must be between 41 to 46°C (106 to 115°F).

·

If the ATF temperature is not between 41 to 46°C (106 to 115°F), turn the ignition switch off and wait until the fluid temperature drops between 41 to 46°C (106 to 115°F).




vii.

for 1UR-FE:

Check the ATF temperature.

NOTICE:
·

The ATF temperature must be between 43 to 48°C (109 to 118°F).

·

If the ATF temperature is not between 43 to 48°C (109 to 118°F), turn the ignition switch off and wait until the fluid temperature drops between 43 to 48°C (109 to 118°F).




viii.

for 1VD-FTV:

According to the display on the GTS, perform the Active Test "Connect the TC and TE1".


ix.

for 1UR-FE:

According to the display on the GTS, perform the Active Test "Connect the TC and TE1".

HINT:

Indicator lights of the combination meter blink to output DTCs when TC and TE1 are connected.



x.

Start the engine.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.




b.
C101492E10
0.947,0.742 1.091,0.924 0.144,0.181 10 1 1.182,0.742 1.352,0.940 0.170,0.198 10 2 2.118,0.742 2.288,0.932 0.170,0.189 10 6 2.548,1.264 2.761,1.453 0.213,0.189 10 16 1.896,0.742 2.066,0.932 0.170,0.189 10 5 1.646,0.742 1.816,0.932 0.170,0.189 10 4 1.414,0.742 1.584,0.932 0.170,0.189 10 3 0.953,1.264 1.145,1.457 0.193,0.193 10 9 1.382,1.264 1.575,1.457 0.193,0.193 10 11 2.368,0.742 2.561,0.935 0.193,0.193 10 7 2.583,0.742 2.775,0.935 0.193,0.193 10 8 1.142,1.264 1.335,1.457 0.193,0.193 10 10 1.606,1.264 1.845,1.471 0.239,0.207 10 12 1.846,1.264 2.035,1.452 0.188,0.188 10 13 2.081,1.264 2.267,1.450 0.186,0.186 10 14 2.316,1.264 2.536,1.438 0.220,0.174 10 15 0.861,0.181 1.105,0.355 0.244,0.174 10 CG 0.058,0.003 0.279,0.186 0.221,0.183 10 *A 1.841,1.871 2.075,2.041 0.235,0.170 10 TC 1.949,1.476 1.949,1.852 false 1.703,0.708 1.189,0.328 false

When not using the GTS:

i.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*A Front View of DLC3


ii.

Start the engine.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.


HINT:

Indicator lights of the meter blink to output DTCs when terminals TC and CG are connected.




c.

Slowly move the shift lever from P to D, then move the shift lever to P.

HINT:

Keep the shift lever in each position for approximately 3 seconds.



d.
C337051E01
0.02,0 0.252,0.200 0.232,0.200 10 *A 0.027,2.429 0.260,2.629 0.232,0.200 10 *B

Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

Standard condition:

Indicator light (D) remains illuminated for 2 seconds and then turns off.


Text in Illustration
*A w/o Multi-information Display
*B w/ Multi-information Display


e.

When using the GTS:

i.

Return the shift lever to P and press OFF on the Active Test display.



f.

When not using the GTS:

i.

Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).



g.

for 1VD-FTV:

Allow the engine to idle until the fluid temperature reaches 41 to 46°C (106 to 115°F).


h.

for 1UR-FE:

Allow the engine to idle until the fluid temperature reaches 43 to 48°C (109 to 118°F).


i.

for 1VD-FTV:

The indicator (D) will come on again when the fluid temperature reaches 41°C (106°F) and will blink when it exceeds 46°C (115°F).

Indicator Indication of ATF Temperature :
Below Proper Temperature Proper Temperature Higher than Proper Temperature
Data List [A/T Oil Temperature 1]
41°C (106°F) or less
Data List [A/T Oil Temperature 1]
41 to 46°C (106 to 115°F)
Data List [A/T Oil Temperature 1]
46°C (115°F) or higher
Indicator light (D)
Turns off
Indicator light (D)
Turns on
Indicator light (D)
Blinking


NOTICE:

Perform the fluid level inspection while the indicator light is on.



j.

for 1UR-FE:

The indicator (D) will come on again when the fluid temperature reaches 43°C (109°F) and will blink when it exceeds 48°C (118°F).

Indicator Indication of ATF Temperature :
Below Proper Temperature Proper Temperature Higher than Proper Temperature
Data List [A/T Oil Temperature 1]
43°C (109°F) or less
Data List [A/T Oil Temperature 1]
43 to 48°C (109 to 118°F)
Data List [A/T Oil Temperature 1]
48°C (118°F) or higher
Indicator light (D)
Turns off
Indicator light (D)
Turns on
Indicator light (D)
Blinking


NOTICE:

Perform the fluid level inspection while the indicator light is on.



Hide 6. FLUID LEVEL CHECK

NOTICE:
·

for 1VD-FTV:

The fluid temperature must be between 41 and 46°C (106 and 115°F) to accurately check the fluid level.

·

for 1UR-FE:

The fluid temperature must be between 43 and 48°C (109 and 118°F) to accurately check the fluid level.



a.
C161094E06
0.625,0.771 0.406,0.771 0.406,0.771 0.406,1.104 false 1.823,0.813 2.813,0.813 false 0.323,1.146 0.563,1.365 0.24,0.219 10 false *a 2.875,0.729 3.094,0.938 0.219,0.208 10 false *1

Remove the overflow plug with the engine idling.


b.

Check that fluid comes out of the overflow tube.

If fluid does not come out, proceed to the "Transmission Refill" procedures.

If fluid comes out, wait until the overflow slows to a trickle and proceed to the "Complete" procedures.

Text in Illustration
*1 Overflow Tube
*a Specified Fluid Level


Hide 7. TRANSMISSION REFILL

a.

Remove the overflow plug.


b.

Remove the refill plug and gasket.


c.

Add ATF into the refill hole until ATF flows from the overflow tube.


d.

Wait until the overflow slows to a trickle and proceed to the "Complete" procedures.


Hide 8. COMPLETE

a.

Install a new gasket and the overflow plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Stop the engine.


c.

Install a new gasket and the refill plug.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)