Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION UNIT
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255263 AUTOMATIC TRANSMISSION UNIT G

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  INSPECTION  


PROCEDURE

Hide 35106 1.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

D001124

a.

Remove the magnets, and use them to collect steel particles.


b.

Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

·

Steel (magnetic): bearing, gear and clutch plate wear

·

Brass (non-magnetic): bush wear



Hide 35790 2.INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY

C161779E01
1.855,0.105 2.218,0.280 0.363,0.175 10 Lock 2.864,0.906 3.212,1.111 0.347,0.204 10 Free

a.

Hold the reverse clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.


Hide 35677C 3.INSPECT REAR CLUTCH DISC

C162758

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35049 4.INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY

C161792

a.

Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

Standard inside diameter:

41.912 to 41.937 mm (1.410 to 1.411 in.)


If the inside diameter is more than the standard, replace the reverse clutch hub.



Hide 35061 5.INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

C161791

a.

Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

Standard inside diameter:

30.200 to 30.225 mm (1.189 to 1.190 in.)


If the inside diameter is more than the standard, replace the forward clutch hub.



Hide 35790H 6.INSPECT NO. 4 1-WAY CLUTCH ASSEMBLY

C161784E01
0.137,0.814 0.520,0.989 0.383,0.175 10 Lock 1.624,0.07 1.966,0.273 0.342,0.202 10 Free

a.

Hold the coast clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.


Hide 35633B 7.INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

C161790

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35685 8.INSPECT COAST CLUTCH DISC

C161789

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35603A 9.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C161788

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

29.65 mm (1.17 in.)



Hide 35667A 10.INSPECT DIRECT CLUTCH DISC

C161787

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35047 11.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

C161786

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.24 mm (0.836 in.)



Hide 35604 12.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C161785

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

19.46 mm (0.766 in.)



Hide 13.INSPECT NO. 3 BRAKE DISC

C161778

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35046 14.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161777

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

15.72 mm (0.619 in.)



Hide 35720 15.INSPECT FRONT PLANETARY GEAR ASSEMBLY

C161773

a.

Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

Standard clearance:

0.2 to 0.6 mm (0.00787 to 0.0236 in.)


If the clearance is more than the standard, replace the front planetary gear assembly.



b.
C161774

Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

Standard inside diameter:

61.005 to 61.030 mm (2.402 to 2.403 in.)


If the inside diameter is more than the standard, replace the front planetary gear.



Hide 35790 16.INSPECT 1-WAY CLUTCH ASSEMBLY

C161775E01
2.13,0.09 2.500,0.277 0.370,0.187 10 Lock 1.046,0.301 1.379,0.492 0.333,0.191 10 Free

a.

Install the 1-way clutch to the 1-way clutch inner race.


b.

Hold the 1-way clutch inner race and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.


c.

Remove the 1-way clutch from the 1-way clutch inner race.


Hide 35681A 17.INSPECT NO. 1 BRAKE DISC

C161776

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35608J 18.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161772

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.05 mm (0.671 in.)



Hide 35682A 19.INSPECT NO. 2 BRAKE DISC

C161770

a.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35045 20.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161771

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

22.66 mm (0.892 in.)



Hide 35750 21.INSPECT CENTER PLANETARY GEAR ASSEMBLY

C161749

a.

Using a feeler gauge, measure the center planetary pinion gear thrust clearance.

Standard clearance:

0.20 to 0.60 mm (0.00787 to 0.0236 in.)


If the clearance is more than the standard, replace the center planetary gear assembly.



Hide 35770C 22.INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY

C161748E01
1.302,0.245 1.663,0.424 0.360,0.179 10 Lock 0.563,1.145 0.895,1.336 0.332,0.191 10 Free

a.

Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.


Hide 35713 23.INSPECT INTERMEDIATE SHAFT

U152325

a.

Using a dial indicator, check the intermediate shaft runout.

Standard runout:

0.03 mm (0.00118 in.)


If the runout is more than the standard, replace the intermediate shaft with a new one.


b.
C161747E01
0.227,3.166 0.372,3.337 0.145,0.170 10 A 0.802,3.166 0.942,3.346 0.139,0.179 10 B 1.357,3.166 1.498,3.343 0.141,0.176 10 C 2.019,3.166 2.161,3.334 0.142,0.167 10 D 2.27,3.166 2.431,3.326 0.161,0.159 10 E

Using a micrometer, check the diameter of the intermediate shaft at the positions shown in the diagram.

Standard diameter:
A:

19.963 to 19.976 mm (0.7859 to 0.7865 in.)

B, C:

30.150 to 30.163 mm (1.187 to 1.188 in.)

D, E:

36.404 to 36.420 mm (1.433 to 1.434 in.)


If the diameter is less than the standard, replace the intermediate shaft with a new one.


Hide 35684 24.INSPECT NO. 4 BRAKE DISC

a.
C161745

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35760 25.INSPECT REAR PLANETARY GEAR ASSEMBLY

a.
C161743

Using a feeler gauge, measure the rear planetary pinion gear thrust clearance.

Standard clearance:

0.2 to 0.6 mm (0.00787 to 0.0236 in.)


If the clearance is more than the standard, replace the planetary gear assembly.



b.
C161744

Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

Standard inside diameter:

20.0 to 20.025 mm (0.787 to 0.788 in.)


If the inside diameter is more than the standard, replace the rear planetary gear assembly.



Hide 35068 26.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C161742

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

23.54 to 23.94 mm (0.927 to 0.943 in.)



Hide 27.INSPECT INDIVIDUAL PISTON OPERATION

C161780E03
1.583,4.073 1.271,4.271 false 1.854,4.073 2.167,4.271 false 1.771,3.167 3.052,3.167 false 1.771,2.802 3.052,2.802 false 1.771,2.396 3.052,2.396 false 2.646,1.198 3.052,1.198 false 0.771,1.135 0.458,1.135 false 1,0.938 0.75,0.25 false 1.271,0.969 1.531,0.25 false 1.552,0.073 1.833,0.25 0.281,0.177 10 false C1 0.198,1.052 0.479,1.229 0.281,0.177 10 false C2 3.104,1.104 3.385,1.281 0.281,0.177 10 false C3 0.49,0.073 0.771,0.25 0.281,0.177 10 false C4 3.104,2.708 3.385,2.885 0.281,0.177 10 false B1 3.104,3.083 3.385,3.26 0.281,0.177 10 false B2 3.104,2.313 3.385,2.49 0.281,0.177 10 false B3 0.802,4.25 1.438,4.427 0.635,0.177 10 true B4 (OUT) 1.958,4.271 2.458,4.448 0.5,0.177 10 true B4 (IN)

a.

Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

HINT:

When inspecting the direct clutch, check with the accumulator piston holes indicated in the illustration.

If there is no sound, disassemble and check the installation condition of the parts.


1.

No. 2 clutch (C2)

2.

No. 3 clutch (C3)

3.

No. 4 clutch (C4)

4.

No. 1 clutch (C1)

5.

No. 3 brake (B3)

6.

No. 1 brake (B1)

7.

No. 2 brake (B2)

8.

No. 4 brake (B4)