Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  Transmission Control Switch Circuit  


DESCRIPTION

When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range between "1" (1st range) and "6" (6th range).

Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM

C176192E34
5.615,1.229 5.844,1.396 0.229,0.167 10 false 25 3.948,2.146 4.417,2.344 0.469,0.198 10 false SFTD 3.948,1.563 4.417,1.76 0.469,0.198 10 false SFTU 4.219,0.969 4.344,1.167 0.125,0.198 10 false S 3.063,0.969 3.302,1.167 0.24,0.198 10 false IG 3.063,2.146 3.302,2.344 0.24,0.198 10 false E 5.948,1.125 6.375,1.323 0.427,0.198 10 false S 5.625,1.813 5.854,1.979 0.229,0.167 10 false 60 5.948,1.729 6.375,1.927 0.427,0.198 10 false SFTU 5.625,2.406 5.854,2.573 0.229,0.167 10 false 59 5.938,2.292 6.365,2.49 0.427,0.198 10 false SFTD 2.802,2.729 3.229,2.927 0.427,0.198 10 false E52 2.802,2.917 4.583,3.115 1.781,0.198 10 false Transmission Control Switch 0.885,1.135 2,1.333 1.115,0.198 10 false from LH-IG Fuse 2.844,1.24 3.01,1.406 0.167,0.167 10 false 3 2.844,2.406 3.031,2.573 0.188,0.167 10 false 5 4.406,1.24 4.771,1.406 0.365,0.167 10 false 7 4.396,1.813 4.677,1.979 0.281,0.167 10 false 2 4.396,2.406 4.719,2.573 0.323,0.167 10 false 1 0.083,2.969 0.875,3.167 0.792,0.198 10 false *1: for LHD 0.083,3.344 0.875,3.542 0.792,0.198 10 false *2: for RHD 6.073,3.375 6.458,3.573 0.385,0.198 10 false ECM 6.073,3.042 6.521,3.24 0.448,0.198 10 false A38*1 6.073,3.208 6.521,3.406 0.448,0.198 10 false A52*2

PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C146679E06
0.056,0.005 2.587,0.372 2.531,0.367 10 Component without harness connected: (Transmission Control Switch) 1.636,1.239 0.955,0.991 false 0.955,1.816 1.636,1.567 false 1.8,1.239 2.647,0.991 false 2.007,1.306 2.688,1.306 false 2.647,1.816 1.966,1.567 false 0.707,0.858 0.959,1.060 0.252,0.202 10 IG 0.767,1.738 0.938,1.940 0.171,0.202 10 S 2.715,0.858 3.224,1.060 0.509,0.202 10 SFTU 2.715,1.195 3.224,1.397 0.509,0.202 10 SFTD 2.715,1.738 2.893,1.940 0.178,0.202 10 E

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
2 (SFTU) - 5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever in S 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever in S 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)
a.
U164504E01
0.469,1.639 0.844,1.873 0.375,0.233 10 E52 0.053,0.006 2.462,0.373 2.409,0.367 10 Front view of wire harness connector: (to Transmission Control Switch) 0.685,2.376 0.879,2.578 0.194,0.202 10 E 1.82,1.712 2.396,1.392 false 2.446,1.249 2.689,1.451 0.243,0.202 10 IG 0.859,2.452 1.435,2.133 false

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Ignition switch ON 11 to 14 V
E52-3 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-5 (E) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U164900E01
0.055,3.773 0.850,3.947 0.795,0.174 10 *1: for LHD 0.055,4.197 0.850,4.371 0.795,0.174 10 *2: for RHD 1.671,1.378 2.046,1.611 0.375,0.233 10 A52 1.671,1.068 2.046,1.301 0.375,0.233 10 A38 2.081,1.378 2.282,1.580 0.200,0.202 10 *2 2.081,1.068 2.282,1.270 0.200,0.202 10 *1 0.055,0.007 2.463,0.374 2.408,0.367 10 Front view of wire harness connector: (to ECM) 0.622,3.257 1.105,3.459 0.483,0.202 10 25 (S) 2.533,3.257 3.227,3.459 0.694,0.202 10 60 (SFTU) 1.418,3.257 2.102,3.459 0.684,0.202 10 59 (SFTD) 1.787,3.242 2.332,2.585 false 0.888,3.242 1.991,2.186 false 2.958,3.242 2.413,2.585 false

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A38-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
A38-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V

for RHD
Tester Connection Condition Specified Condition
A52-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
A52-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V



c.

Turn the ignition switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-60 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A38-59 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A38-60 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
A38-59 (SFTD) - Body ground Shift lever in S 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-60 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A52-59 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A52-60 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
A52-59 (SFTD) - Body ground Shift lever in S 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR