Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0705 When one of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
·

P input signal

·

N input signal

·

R input signal

·

D input signal


(B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
·

NSW input signal

·

R input signal

·

D input signal


(C) Any of the following signals are ON for 2.0 sec. or more when the shift lever is in S (2 trip detection logic).
·

NSW input signal

·

P input signal

·

N input signal

·

R input signal


(D) All the signals are OFF simultaneously for the P, R, N and D positions (2 trip detection logic).
·

Park/neutral position switch

·

Transmission control switch (Transmission floor shift assembly)

·

Open or short in park/neutral position switch circuit

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C285352E05
5.802,6.396 6.188,6.594 0.385,0.198 10 false ECM 4.302,1.875 5.135,2.073 0.833,0.198 10 false to ST Relay 0.333,1.74 1.75,2.292 1.417,0.552 10 false from Certification ECU (Smart Key ECU Assembly) (STAR) 5.25,5.75 5.563,5.948 0.313,0.198 10 false A38 5.583,5.75 5.896,5.948 0.313,0.198 10 false S 5.292,5.552 5.51,5.75 0.219,0.198 10 false 25 5.25,4.177 5.563,4.375 0.313,0.198 10 false C45 5.583,4.167 5.896,4.365 0.313,0.198 10 false P 5.313,3.958 5.531,4.156 0.219,0.198 10 false 31 5.25,3.573 5.563,3.771 0.313,0.198 10 false C45 5.583,3.573 5.896,3.771 0.313,0.198 10 false R 5.313,3.365 5.531,3.563 0.219,0.198 10 false 30 5.25,2.969 5.594,3.167 0.344,0.198 10 false C45 5.583,2.917 5.896,3.115 0.313,0.198 10 false N 5.313,2.76 5.531,2.958 0.219,0.198 10 false 29 5.26,2.375 5.573,2.573 0.313,0.198 10 false C45 5.583,2.385 5.896,2.583 0.313,0.198 10 false D 5.313,2.156 5.531,2.354 0.219,0.198 10 false 28 5.24,1.198 5.573,1.396 0.333,0.198 10 false C45 5.583,1.219 6,1.417 0.417,0.198 10 false NSW 5.313,0.948 5.531,1.146 0.219,0.198 10 false 49 3.76,2.031 3.979,2.229 0.219,0.198 10 false 5 3.76,2.479 3.979,2.677 0.219,0.198 10 false 7 3.76,3.083 3.979,3.281 0.219,0.198 10 false 9 3.76,4.281 3.979,4.479 0.219,0.198 10 false 6 3.76,3.677 3.979,3.875 0.219,0.198 10 false 1 3.76,5.844 3.979,6.042 0.219,0.198 10 false 7 3.594,1.75 3.813,1.948 0.219,0.198 10 false L 3.5,2.188 3.771,2.385 0.271,0.198 10 false DL 3.5,2.792 3.771,2.99 0.271,0.198 10 false NL 2.76,3.104 3.031,3.302 0.271,0.198 10 false RB 3.5,3.396 3.771,3.594 0.271,0.198 10 false RL 3.5,3.99 3.771,4.188 0.271,0.198 10 false PL 3.583,5.573 3.854,5.771 0.271,0.198 10 false S 2.76,1.75 2.979,1.948 0.219,0.198 10 false B 2.76,5.573 3.031,5.771 0.271,0.198 10 false IG 2.583,2.031 2.802,2.229 0.219,0.198 10 false 4 2.573,3.385 2.792,3.583 0.219,0.198 10 false 2 2.604,5.844 2.875,6.042 0.271,0.198 10 false 3 2.292,6.219 2.604,6.417 0.313,0.198 10 false E52 2.292,6.406 4.146,6.604 1.854,0.198 10 false Transmission Control Switch 0.146,5.708 1.813,5.906 1.667,0.198 10 false from ECU-IG NO. 2 Fuse 0.469,3.229 1.823,3.427 1.354,0.198 10 false from BKUP LP Fuse 2.302,4.625 2.615,4.823 0.313,0.198 10 false C24 2.302,4.813 4.125,5.01 1.823,0.198 10 false Park/Neutral Position Switch 0.104,0.052 0.813,0.281 0.708,0.229 12 false for LHD:

C200876E27
5.813,6.406 6.198,6.604 0.385,0.198 10 false ECM 4.313,1.885 5.146,2.083 0.833,0.198 10 false to ST Relay 0.063,1.625 1.833,2.229 1.771,0.604 10 false from Certification ECU (Smart Key ECU Assembly) (STAR) 5.25,5.75 5.563,5.948 0.313,0.198 10 false A52 5.583,5.719 5.896,5.917 0.313,0.198 10 false S 5.302,5.563 5.521,5.76 0.219,0.198 10 false 25 5.26,4.177 5.573,4.375 0.313,0.198 10 false C46 5.583,4.125 5.896,4.323 0.313,0.198 10 false P 5.313,3.958 5.531,4.156 0.219,0.198 10 false 31 5.26,3.573 5.573,3.771 0.313,0.198 10 false C46 5.583,3.521 5.896,3.719 0.313,0.198 10 false R 5.313,3.385 5.531,3.583 0.219,0.198 10 false 30 5.26,2.979 5.573,3.177 0.313,0.198 10 false C46 5.583,2.927 5.896,3.125 0.313,0.198 10 false N 5.323,2.771 5.542,2.969 0.219,0.198 10 false 29 5.25,2.375 5.563,2.573 0.313,0.198 10 false C46 5.583,2.323 5.896,2.521 0.313,0.198 10 false D 5.302,2.177 5.521,2.375 0.219,0.198 10 false 28 5.25,1.198 5.563,1.396 0.313,0.198 10 false C46 5.583,1.146 6,1.344 0.417,0.198 10 false NSW 5.302,1.01 5.521,1.208 0.219,0.198 10 false 49 3.771,2.042 3.99,2.24 0.219,0.198 10 false 5 3.771,2.49 3.99,2.688 0.219,0.198 10 false 7 3.771,3.094 3.99,3.292 0.219,0.198 10 false 9 3.771,4.26 3.99,4.458 0.219,0.198 10 false 6 3.771,3.688 3.99,3.885 0.219,0.198 10 false 1 3.771,5.854 3.99,6.052 0.219,0.198 10 false 7 3.563,1.813 3.781,2.01 0.219,0.198 10 false L 3.479,2.25 3.75,2.448 0.271,0.198 10 false DL 3.479,2.844 3.75,3.042 0.271,0.198 10 false NL 2.771,3.156 3.042,3.354 0.271,0.198 10 false RB 3.5,3.396 3.771,3.594 0.271,0.198 10 false RL 3.458,4.052 3.729,4.25 0.271,0.198 10 false PL 3.563,5.625 3.833,5.823 0.271,0.198 10 false S 2.771,1.813 2.99,2.01 0.219,0.198 10 false B 2.771,5.625 3.042,5.823 0.271,0.198 10 false IG 2.563,2.052 2.781,2.25 0.219,0.198 10 false 4 2.552,3.406 2.771,3.604 0.219,0.198 10 false 2 2.583,5.844 2.854,6.042 0.271,0.198 10 false 3 2.063,2.469 2.344,2.667 0.281,0.198 10 false *2 2.063,1.792 2.344,1.99 0.281,0.198 10 false *1 2.292,6.229 2.604,6.427 0.313,0.198 10 false E52 2.292,6.417 4.146,6.615 1.854,0.198 10 false Transmission Control Switch 0.208,5.76 1.844,5.979 1.635,0.219 10 false from ECU-IG NO. 2 Fuse 0.073,6.979 2.5,7.177 2.427,0.198 10 false *1: w/ Entry and Start System 0.073,7.354 2.51,7.552 2.438,0.198 10 false *2: w/o Entry and Start System 0.458,3.281 1.865,3.49 1.406,0.208 10 false from BKUP LP Fuse 0.135,2.604 1.854,2.802 1.719,0.198 10 false from Ignition Switch (ST2) 2.313,4.635 2.625,4.833 0.313,0.198 10 false C24 2.313,4.823 4.135,5.021 1.823,0.198 10 false Park/Neutral Position Switch 0.177,0.177 1.01,0.375 0.833,0.198 12 false for RHD:

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
Shift lever:
·

In P or N: ON

·

Not in P or N: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever:
·

In R: ON

·

Not in R: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever:
·

In P: ON

·

Not in P: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever:
·

In N: ON

·

Not in N: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever:
·

In D: ON

·

Not in D: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not in "-" (down-shift)


-



PROCEDURE

1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C146745E28
0.056,0.004 2.638,0.371 2.582,0.367 10 Component without harness connected: (Park/Neutral Position Switch) 1.279,0.98 1.493,1.161 0.213,0.181 10 RB 0.882,0.98 1.019,1.161 0.137,0.181 10 B 1.633,1.653 1.556,1.063 false 1.65,2.523 1.727,1.933 false 1.997,2.523 1.92,1.933 false 2.414,2.433 2.561,2.614 0.147,0.181 10 L 2.04,2.433 2.250,2.614 0.210,0.181 10 PL 1.382,2.433 1.592,2.614 0.210,0.181 10 DL 0.827,2.433 1.037,2.614 0.210,0.181 10 NL 2.209,0.98 2.422,1.161 0.213,0.181 10 RL 1.824,1.653 2.175,1.063 false 1.082,2.523 1.433,1.933 false 1.386,1.653 1.034,1.063 false 2.376,2.523 2.024,1.933 false

Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever in N Below 1 Ω
2 (RB) - 7 (DL)
·

Shift lever in D

·

Shift lever in S, "+" or "-"


Below 1 Ω
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL)
·

Shift lever not in D

·

Shift lever not in S, "+" or "-"


10 kΩ or higher




OK

2.INSPECT TRANSMISSION CONTROL SWITCH

NG

2.INSPECT TRANSMISSION CONTROL SWITCH
a.
C146679E04
0.056,0.005 2.587,0.372 2.531,0.367 10 Component without harness connected: (Transmission Control Switch) 1.636,1.239 0.955,0.991 false 0.955,1.816 1.636,1.567 false 0.707,0.858 0.959,1.060 0.252,0.202 10 IG 0.767,1.738 0.939,1.940 0.171,0.202 10 S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Result:
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C




A

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)

B

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

C

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)
a.
U164505E02
1.823,1.667 2.167,1.073 false 0.135,0.104 2.531,0.469 2.396,0.365 10 false Front view of wire harness connector: (to Park/Neutral Position Switch) 0.406,1.677 0.781,1.906 0.375,0.229 10 false C24 2.198,0.885 2.469,1.063 0.271,0.177 10 false RB

Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-2 (RB) - Body ground Ignition switch ON 11 to 14 V
C24-2 (RB) - Body ground Ignition switch off Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY)
a.
U164503E02
1.823,1.771 2.396,1.448 false 0.479,1.698 0.854,1.927 0.375,0.229 10 false E52 0.135,0.083 2.479,0.469 2.344,0.385 10 false Front view of wire harness connector: (to Transmission Control Switch) 2.458,1.365 2.698,1.563 0.24,0.198 10 false IG

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Ignition switch ON 11 to 14 V
E52-3 (IG) - Body ground Ignition switch off Below 1 V




OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
U164879E02
2.188,3.063 1,2.135 false 1.031,3.052 0.833,2.125 false 0.354,3.271 0.667,2.219 false 1.635,3.26 0.917,2.135 false 2.969,3.26 1.094,2.135 false 0.115,0.094 2.521,0.458 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 0.813,3.083 1.25,3.281 0.438,0.198 10 false 28 (D) 0.104,3.292 0.771,3.49 0.667,0.198 10 false 49 (NSW) 1.604,1.438 1.979,1.667 0.375,0.229 10 false C46 1.594,1.125 1.969,1.354 0.375,0.229 10 false C45 1.99,1.385 2.188,1.583 0.198,0.198 10 false *2 1.99,1.073 2.188,1.271 0.198,0.198 10 false *1 0.052,3.833 0.844,4.031 0.792,0.198 10 false *1: for LHD 0.052,4.146 0.844,4.344 0.792,0.198 10 false *2: for RHD 1.458,3.271 1.896,3.469 0.438,0.198 10 false 29 (N) 2.021,3.083 2.458,3.281 0.438,0.198 10 false 30 (R) 2.802,3.292 3.24,3.49 0.438,0.198 10 false 31 (P)

a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
·

C45-31 (P) - Body ground

·

C45-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever in P


11 to 14 V
C45-30 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
·

C45-29 (N) - Body ground

·

C45-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever in N


11 to 14 V
C45-28 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
·

C45-31 (P) - Body ground

·

C45-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever not in P


Below 1 V
C45-30 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
·

C45-29 (N) - Body ground

·

C45-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever not in N


Below 1 V
C45-28 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V

for RHD
Tester Connection Condition Specified Condition
·

C46-31 (P) - Body ground

·

C46-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever in P


11 to 14 V
C46-30 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
·

C46-29 (N) - Body ground

·

C46-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever in N


11 to 14 V
C46-28 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
·

C46-31 (P) - Body ground

·

C46-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever not in P


Below 1 V
C46-30 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
·

C46-29 (N) - Body ground

·

C46-49 (NSW) - Body ground


·

Ignition switch ON

·

Shift lever not in N


Below 1 V
C46-28 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V


HINT:

*: The voltage will drop slightly due to the turning on of the back-up light.




OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U164897E01
0.055,3.774 0.850,3.949 0.795,0.174 10 *1: for LHD 0.055,4.198 0.850,4.373 0.795,0.174 10 *2: for RHD 1.669,1.382 2.044,1.615 0.375,0.233 10 A52 1.669,1.073 2.044,1.306 0.375,0.233 10 A38 2.079,1.382 2.279,1.584 0.200,0.202 10 *2 2.079,1.073 2.279,1.275 0.200,0.202 10 *1 0.053,0.011 2.461,0.378 2.408,0.367 10 Front view of wire harness connector: (to ECM) 2.119,3.247 2.590,3.449 0.471,0.202 10 25 (S) 2.292,3.232 1.983,2.177 false

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A38-25 (S) - Body ground Shift lever in S, "+" or "-" 11 to 14 V
A38-25 (S) - Body ground Shift lever not in S, "+" or "-" Below 1 V

for RHD
Tester Connection Condition Specified Condition
A52-25 (S) - Body ground Shift lever in S, "+" or "-" 11 to 14 V
A52-25 (S) - Body ground Shift lever not in S, "+" or "-" Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR