Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P0976  Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2)  P0977  Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2)  


DESCRIPTION

Shifting from 1st to 6th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely. Also, the ECM stops sending current to the open or short circuited solenoid (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV)>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0976 The ECM detects a short in the solenoid valve S2 circuit 2 times when the solenoid valve S2 is operated (1 trip detection logic).
·

Short in shift solenoid valve S2 circuit

·

Shift solenoid valve S2

·

ECM


P0977 The ECM detects an open in the solenoid valve S2 circuit 2 times when the solenoid valve S2 is not operated (1 trip detection logic).
·

Open in shift solenoid valve S2 circuit

·

Shift solenoid valve S2

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S2 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve S2 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S2 circuit.

When the shift solenoid valve S2 is OFF, if its resistance is 100 kΩ or higher, the ECM determines there is an open in the shift solenoid valve S2 circuit (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV)>FAIL-SAFE CHART).

WIRING DIAGRAM

C178086E34
2.771,0.917 3,1.083 0.229,0.167 10 false 15 5.542,0.906 5.771,1.073 0.229,0.167 10 false 8 2.479,0.677 2.813,0.875 0.333,0.198 10 false S2 5.771,0.771 6.063,0.969 0.292,0.198 10 false S2 1.01,2.542 1.438,2.74 0.427,0.198 10 false C34 1.01,2.708 2.708,2.906 1.698,0.198 10 false No. 1 Transmission Wire 1.01,1.5 2.646,1.74 1.635,0.24 10 false Shift Solenoid Valve S2 5.896,3.031 6.344,3.198 0.448,0.167 10 false C46*2 5.896,2.875 6.344,3.042 0.448,0.167 10 false C45*1 5.896,3.177 6.323,3.375 0.427,0.198 10 false ECM 0.052,3 0.833,3.198 0.781,0.198 10 false *1: for LHD 0.052,3.365 0.833,3.563 0.781,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

HINT:

The shift solenoid valve S2 is turned ON/OFF normally when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S2 ON ON OFF OFF OFF ON


PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S2)
a.
C159421E23
0.887,2.631 1.321,2.776 0.434,0.145 10 S2 0.058,0.046 2.640,0.413 2.582,0.367 10 Component without harness connected: (No. 1 Transmission Wire) 1.295,2.024 1.036,2.592 false

Disconnect the No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
15 (S2) - Body ground 20°C (68°F) 11 to 15 Ω




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE S2
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
U164872E01
0.053,0.002 2.462,0.369 2.408,0.367 10 Front view of wire harness connector: (to ECM) 1.581,1.382 1.957,1.615 0.375,0.233 10 C46 1.581,1.072 1.956,1.305 0.375,0.233 10 C45 1.991,1.382 2.191,1.584 0.200,0.202 10 *2 1.991,1.072 2.191,1.274 0.200,0.202 10 *1 0.055,3.684 0.846,3.886 0.791,0.202 10 *1: for LHD 0.055,4.142 0.846,4.344 0.791,0.202 10 *2: for RHD 0.73,3.203 1.107,2.003 false 0.477,3.218 1.013,3.420 0.536,0.202 10 8 (S2)

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-8 (S2) - Body ground 20°C (68°F) 11 to 15 Ω

for RHD
Tester Connection Condition Specified Condition
C46-8 (S2) - Body ground 20°C (68°F) 11 to 15 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE S2
a.
C160564E01
2.349,0.818 2.580,1.001 0.231,0.184 10 (+) 0.056,0 1.633,0.186 1.577,0.186 10 Shift Solenoid Valve S2: 3.116,0.818 3.347,1.001 0.231,0.184 10 (-)

Remove the shift solenoid valve S2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S2 connector

·

Battery negative (-) → Shift solenoid valve S2 body


Valve moves and makes an operating noise




OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE

NG