Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code DTC Detection Condition Trouble Area
P0724 The stop light switch remains on even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during "stop and go" driving, the ECM interprets this as a fault in the stop light switch, the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) five times for 2 driving cycles in order to detect a malfunction.

WIRING DIAGRAM

C146704E11
5.234,1.447 5.464,1.616 0.230,0.170 10 36 3.944,1.447 4.174,1.616 0.230,0.170 10 2 4.723,1.447 4.953,1.616 0.230,0.170 10 1 2.076,1.539 2.397,1.734 0.321,0.195 10 ALT 3.006,1.539 3.685,1.734 0.679,0.195 10 STOP 5.536,1.35 5.958,1.546 0.422,0.195 10 STP 1.641,2.392 2.170,2.587 0.529,0.195 10 Battery 3.825,1.689 4.141,1.885 0.316,0.195 10 A30 3.825,1.868 5.085,2.063 1.260,0.195 10 Stop Light Switch 0.044,2.958 0.838,3.132 0.795,0.174 10 *1: for LHD 0.044,3.303 0.838,3.478 0.795,0.174 10 *2: for RHD 5.701,3.238 6.083,3.434 0.382,0.196 10 ECM 5.701,2.864 6.144,3.066 0.443,0.202 10 A38*1 5.701,3.05 6.144,3.252 0.443,0.202 10 A52*2

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the tester, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
Brake pedal:
·

Depressed: ON

·

Released: OFF


-



PROCEDURE

1.INSPECT STOP LIGHT SWITCH
a.
C171632E01
1.656,1.34 1.116,0.984 false 2.337,1.87 1.797,1.514 false 1.797,1.34 2.337,0.984 false 1.116,1.87 1.656,1.514 false 0.968,0.865 1.092,1.067 0.124,0.202 10 2 2.381,0.865 2.520,1.067 0.139,0.202 10 1 0.968,1.756 1.095,1.958 0.126,0.202 10 4 2.381,1.756 2.531,1.958 0.150,0.202 10 3 0.882,2.331 1.137,2.545 0.255,0.215 10 Pin 0.027,3.792 0.555,4.143 0.528,0.351 10 Not Pushed 0.795,3.792 1.323,3.990 0.528,0.198 10 Pushed 0.595,3.146 0.752,2.451 0.752,2.451 0.834,2.451 false 0.058,0.027 2.622,0.394 2.564,0.367 10 Component without harness connected: (Stop Light Switch)

Remove the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
3 - 4 Pin pushed Below 1 Ω
1 - 2 Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

NG

REPLACE STOP LIGHT SWITCH

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)
a.
U164898E01
0.055,3.775 0.850,3.949 0.795,0.174 10 *1: for LHD 0.055,4.199 0.850,4.373 0.795,0.174 10 *2: for RHD 1.672,1.382 2.047,1.615 0.375,0.233 10 A52 1.672,1.073 2.047,1.306 0.375,0.233 10 A38 2.082,1.382 2.282,1.584 0.200,0.202 10 *2 2.082,1.073 2.282,1.275 0.200,0.202 10 *1 0.055,0.008 2.463,0.375 2.408,0.367 10 Front view of wire harness connector: (to ECM) 1.964,3.246 2.657,3.448 0.693,0.202 10 36 (STP) 2.289,3.231 1.981,2.408 false

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A38-36 (STP) - Body ground Brake pedal depressed 11 to 14 V
A38-36 (STP) - Body ground Brake pedal released Below 1 V

for RHD
Tester Connection Condition Specified Condition
A52-36 (STP) - Body ground Brake pedal depressed 11 to 14 V
A52-36 (STP) - Body ground Brake pedal released Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR