Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The amount of current flow to the solenoid is controlled by the duty ratio* of the ECM output signal. During the lock-up operation, if the duty ratio increases, the lock-up hydraulic pressure increases.

C221407E01
4.729,2.135 5.031,1.188 5.031,1.188 5.094,1.188 true 4.969,2.323 5.125,2.688 5.125,2.688 5.188,2.688 true 5.76,2.396 5.917,2.688 5.917,2.688 5.979,2.688 true 6.031,2.594 6.917,2.813 0.885,0.219 10 false Solenoid Coil 0.135,0.688 1.385,0.906 1.25,0.219 10 false Hydraulic Pressure 2.573,3.01 3.135,3.229 0.563,0.219 10 false Current 5.24,2.615 5.771,2.833 0.531,0.219 10 false Sleeve 5.167,1.104 6.01,1.323 0.844,0.219 10 false Spool Valve

DTC Code DTC Detection Condition Trouble Area
P2759 An open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

ECM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLU circuit is detected, the ECM determines that there is a malfunction. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C178085E48
2.792,0.938 3.021,1.104 0.229,0.167 10 false 12 0.813,0.969 1.042,1.135 0.229,0.167 10 false 2 0.813,1.813 1.042,1.979 0.229,0.167 10 false 1 5.448,0.927 5.677,1.094 0.229,0.167 10 false 15 2.323,0.698 2.75,0.896 0.427,0.198 10 false SLU+ 2.813,2.146 3.042,2.313 0.229,0.167 10 false 4 2.302,1.906 2.729,2.104 0.427,0.198 10 false SLU- 5.771,0.802 6.198,1 0.427,0.198 10 false SLU+ 5.448,2.156 5.677,2.323 0.229,0.167 10 false 14 5.781,2.031 6.208,2.229 0.427,0.198 10 false SLU- 1.031,2.49 1.458,2.688 0.427,0.198 10 false C34 1.031,2.667 2.729,2.865 1.698,0.198 10 false No. 1 Transmission Wire 1.031,1.365 2.677,1.594 1.646,0.229 10 false Shift Solenoid Valve SLU 5.917,2.979 6.396,3.146 0.479,0.167 10 false C46*2 5.917,2.823 6.396,2.99 0.479,0.167 10 false C45*1 5.917,3.135 6.344,3.333 0.427,0.198 10 false ECM 0.115,3 0.917,3.198 0.802,0.198 10 false *1: for LHD 0.115,3.365 0.917,3.563 0.802,0.198 10 false *2: for RHD

PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C159421E15
1.235,2.631 1.669,2.776 0.434,0.145 10 SLU+ 0.058,0.046 2.640,0.413 2.582,0.367 10 Component without harness connected: (No. 1 Transmission Wire) 1.963,2.631 2.400,2.776 0.437,0.145 10 SLU- 1.731,2.024 1.472,2.592 false 1.798,1.804 2.103,2.592 false

Disconnect the No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SLU+) - 4 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
12 (SLU+) - Body ground Always 10 kΩ or higher
4 (SLU-) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
U164878E01
0.053,0.002 2.462,0.369 2.408,0.367 10 Front view of wire harness connector: (to ECM) 1.581,1.382 1.957,1.615 0.375,0.233 10 C46 1.581,1.072 1.956,1.305 0.375,0.233 10 C45 1.991,1.382 2.191,1.584 0.200,0.202 10 *2 1.991,1.072 2.191,1.274 0.200,0.202 10 *1 0.055,3.684 0.846,3.886 0.791,0.202 10 *1: for LHD 0.055,4.142 0.846,4.344 0.791,0.202 10 *2: for RHD 1.254,3.201 1.631,2.005 false 0.845,3.216 1.493,3.418 0.648,0.202 10 14 (SLU-) 2.096,3.201 1.719,2.005 false 1.809,3.216 2.517,3.418 0.708,0.202 10 15 (SLU+)

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-15 (SLU+) - C45-14 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C45-15 (SLU+) - Body ground Always 10 kΩ or higher
C45-14 (SLU-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-15 (SLU+) - C46-14 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C46-15 (SLU+) - Body ground Always 10 kΩ or higher
C46-14 (SLU-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLU
a.

Remove the shift solenoid valve SLU.


C358531E02
1.875,1.208 2.344,0.844 false 1.594,1.229 1.073,0.813 false 1.865,3.344 2.333,2.979 false 1.583,3.344 1.063,2.927 false 0.104,0.042 2.573,0.417 2.469,0.375 10 false Component without harness connected: (Shift Solenoid Valve SLU) 2.406,0.688 2.563,0.885 0.156,0.198 10 false 1 0.948,0.667 1.104,0.865 0.156,0.198 10 false 2 2.375,2.833 2.531,3.031 0.156,0.198 10 false 1 0.906,2.792 1.063,2.99 0.156,0.198 10 false 2 1.271,4.344 1.479,4.542 0.208,0.198 10 false (+) 2.01,4.333 2.219,4.531 0.208,0.198 10 false (-)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise




OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE

NG