Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P0748  Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)  


DESCRIPTION

Shifting from 1st to 6th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV)>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0748 The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gear (1 trip detection logic).
The output signal duty equals 100%.
HINT:

The SL1 output signal duty is less than 100% under normal conditions.


·

Open or short in shift solenoid valve SL1 circuit

·

Shift solenoid valve SL1

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Also, the ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the open or short circuited solenoid.

While driving and shifting between 4th and 5th gears, if the ECM detects an open or short in the shift solenoid valve SL1 circuit, the ECM determines that there is a malfunction (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV)>FAIL-SAFE CHART).

WIRING DIAGRAM

C178085E06
2.795,0.88 3.025,1.050 0.230,0.170 10 11 0.813,0.973 1.043,1.143 0.230,0.170 10 1 0.813,1.759 1.043,1.929 0.230,0.170 10 2 5.492,0.886 5.721,1.056 0.230,0.170 10 13 2.318,0.667 2.740,0.862 0.422,0.195 10 SL1+ 2.815,2.096 3.045,2.266 0.230,0.170 10 3 2.318,1.885 2.740,2.080 0.422,0.195 10 SL1- 5.78,0.783 6.202,0.978 0.422,0.195 10 SL1+ 5.492,2.11 5.721,2.280 0.230,0.170 10 12 5.78,2.002 6.202,2.198 0.422,0.195 10 SL1- 1.034,2.492 1.456,2.688 0.422,0.195 10 C34 1.034,2.671 2.730,2.866 1.695,0.195 10 No. 1 Transmission Wire 1.034,1.362 2.686,1.590 1.651,0.229 10 Shift Solenoid Valve SL1 5.918,2.979 6.394,3.149 0.475,0.170 10 C46*2 5.918,2.824 6.394,2.994 0.475,0.170 10 C45*1 5.918,3.132 6.341,3.327 0.422,0.195 10 ECM 0.045,3 0.847,3.196 0.802,0.195 10 *1: for LHD 0.045,3.361 0.847,3.557 0.802,0.195 10 *2: for RHD

CAUTION / NOTICE / HINT

HINT:

The shift solenoid valve SL1 turns ON/OFF normally when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL1 OFF OFF OFF OFF ON ON


PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL1)
a.
C159421E20
1.377,2.631 1.811,2.776 0.434,0.145 10 SL1+ 0.058,0.046 2.640,0.413 2.582,0.367 10 Component without harness connected: (No. 1 Transmission Wire) 2.105,2.631 2.542,2.776 0.437,0.145 10 SL1- 1.872,2.024 1.614,2.592 false 1.94,1.804 2.245,2.592 false

Disconnect the No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (SL1+) - 3 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
11 (SL1+) - Body ground Always 10 kΩ or higher
3 (SL1-) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL1
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
U164869E01
0.054,0.005 2.463,0.372 2.408,0.367 10 Front view of wire harness connector: (to ECM) 1.611,3.181 2.362,3.383 0.751,0.202 10 13 (SL1+) 1.034,3.166 1.46,2.005 false 0.53,3.181 1.259,3.383 0.728,0.202 10 12 (SL1-) 1.967,3.166 1.541,2.005 false 1.564,1.38 1.939,1.613 0.375,0.233 10 C46 1.564,1.07 1.939,1.303 0.375,0.233 10 C45 1.974,1.38 2.174,1.582 0.200,0.202 10 *2 1.974,1.07 2.174,1.272 0.200,0.202 10 *1 0.055,3.692 0.846,3.894 0.791,0.202 10 *1: for LHD 0.055,4.15 0.846,4.352 0.791,0.202 10 *2: for RHD

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-13 (SL1+) - C45-12 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
C45-13 (SL1+) - Body ground Always 10 kΩ or higher
C45-12 (SL1-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-13 (SL1+) - C46-12 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
C46-13 (SL1+) - Body ground Always 10 kΩ or higher
C46-12 (SL1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL1
a.

Remove the shift solenoid valve SL1.


C358507E01
1.104,3.021 1.552,3.292 false 1.844,1.198 2.292,0.896 false 1.854,3.323 2.344,2.938 false 1.104,0.917 1.552,1.188 false 0.229,0.042 2.677,0.385 2.448,0.344 10 false Component without harness connected: (Shift Solenoid Valve SL1) 0.969,0.792 1.125,0.99 0.156,0.198 10 false 2 2.344,0.792 2.5,0.99 0.156,0.198 10 false 1 0.969,2.844 1.125,3.042 0.156,0.198 10 false 2 2.406,2.813 2.563,3.01 0.156,0.198 10 false 1 1.219,4.323 1.417,4.521 0.198,0.198 10 false (-) 2.031,4.323 2.229,4.521 0.198,0.198 10 false (+)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise




OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE

NG