Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P2742  Transmission Fluid Temperature Sensor "B" Circuit Low Input  P2743  Transmission Fluid Temperature Sensor "B" Circuit High Input  


DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor is on the transmission, just in front of the oil cooler inlet pipeline.

If the ECM detects an abnormally high ATF temperature near this sensor, it illuminates the warning light.

HINT:
·

The temperature of ATF easily rises when towing, climbing hills, in traffic, etc.

·

If the ATF temperature sensor becomes short-circuited, the signal that indicates that the ATF temperature is 150°C (302°F) or higher is input into the ECM.



Vehicle conditions when the sensor is normal and when the sensor is short-circuited are indicated in the table below.

No. 2 ATF Temperature Sensor State Detection Condition Symptom Recovery Condition
Sensor is normal ATF temperature higher than 150°C (302°F) ATF temperature warning light remains on ATF temperature below 135°C (275°F)*1
ATF temperature higher than 130°C (266°F) Shift point too high ATF temperature below 110°C (230°F)
When conditions (a) and (b) are satisfied.
(a) ATF temperature higher than 130°C (266°F)
(b) Engine coolant temperature higher than 95°C (203°F)
Lock-up at 3rd gear*2 ATF temperature below 110°C (230°F)*1 and engine coolant temperature higher than 95°C (203°F)
Sensor is short-circuited Any conditions
·

ATF temperature warning light blinks or message is displayed in combination meter

·

Shift point too high


Symptoms still occur
Engine coolant temperature higher than 95°C (203°F) Lock-up at 3rd gear*2 Symptoms still occur

HINT:

*1: When the ATF temperature is in the normal range, it decreases to below 135°C (275°F) within 5 minutes with the shift lever in P or N in an idling state.

*2: When the ATF temperature is normal, transmission lock-up occurs in 5th or 6th gear with the shift lever in D or the S6 range, in 5th gear with the shift lever in the S5 range, and 4th gear with the shift lever in the S4 range.


DTC Code DTC Detection Condition Trouble Area
P2742 The No. 2 ATF temperature sensor resistance is below 25 Ω (0.046 V) for 0.5 sec. or more (1 trip detection logic).
·

Short in No. 2 ATF temperature sensor circuit

·

No. 1 transmission wire (No. 2 ATF temperature sensor)

·

ECM


P2743 When 15 min. or more have elapsed after the engine is started, the No. 2 ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more (1 trip detection logic).
·

Open in No. 2 ATF temperature sensor circuit

·

No. 1 transmission wire (No. 2 ATF temperature sensor)

·

ECM



MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is below 25 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM stores a DTC, and the ATF temperature warning light blinks or a message is displayed in the combination meter.

HINT:
·

*1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.

·

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

·

The ATF temperature can be checked on the intelligent tester display.



CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the tester, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 2 No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall test: Approximately 80°C (176°F)

·

With engine cold: Equal to ambient temperature


If the value is -40°C (-40°F) or 150°C (302°F), the No. 2 ATF temperature sensor circuit is open or shorted.

HINT:
·

When DTC P2742 is stored and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.

·

When DTC P2743 is stored and the intelligent tester output is -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the tester in order to check if a malfunction exists.



Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit



PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (NO. 2 ATF TEMPERATURE SENSOR)
a.
C159421E18
1.523,2.631 1.957,2.776 0.434,0.145 10 OT2+ 0.058,0.046 2.640,0.413 2.582,0.367 10 Component without harness connected: (No. 1 Transmission Wire) 2.202,2.631 2.639,2.776 0.437,0.145 10 OT2- 2.018,2.024 1.76,2.592 false 2.086,1.804 2.391,2.592 false

Disconnect the No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (OT2-) - 10 (OT2+) Always 25 Ω to 156 kΩ
2 (OT2-) - Body ground Always 10 kΩ or higher
10 (OT2+) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range of one of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.


Resistance (Reference):
ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

REPAIR OR REPLACE NO. 2 ATF TEMPERATURE SENSOR (NO. 1 TRANSMISSION WIRE)

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
a.
U164877E02
1.073,3.229 1.448,2.615 false 1.906,3.24 1.531,2.625 false 0.073,0.063 2.479,0.427 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.583,1.427 1.958,1.656 0.375,0.229 10 false C46 1.583,1.115 1.958,1.344 0.375,0.229 10 false C45 1.99,1.385 2.188,1.583 0.198,0.198 10 false *2 1.99,1.073 2.188,1.271 0.198,0.198 10 false *1 0.104,3.688 0.896,3.885 0.792,0.198 10 false *1: for LHD 0.115,4.052 0.906,4.25 0.792,0.198 10 false *2: for RHD 0.5,3.25 1.292,3.448 0.792,0.198 10 false 121 (THO2) 1.604,3.25 2.396,3.448 0.792,0.198 10 false 122 (ETHA)

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-121 (THO2) - C45-122 (ETHA) Always 25 Ω to 156 kΩ
C45-121 (THO2) - Body ground Always 10 kΩ or higher
C45-122 (ETHA) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-121 (THO2) - C46-122 (ETHA) Always 25 Ω to 156 kΩ
C46-121 (THO2) - Body ground Always 10 kΩ or higher
C46-122 (ETHA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR