When 2nd mode is selected with the ECT 2nd switch, the ECM controls the solenoid valves and the transmission starts from 2nd gear.
The 2nd mode is the system that operates the throttle motor to control engine output to reduce skidding of the driving wheels, and guarantee takeoff acceleration, driving straightness and turning stability.
When the shift lever is in D, the transmission automatically shifts up through 3rd to 6th as usual.
Refer to Pattern Select Switch Power Mode Circuit (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV)>Pattern Select Switch Power Mode Circuit).
When the ECT 2nd switch is pushed, switch contact is made and 2nd mode is selected. To cancel 2nd mode, push the ECT 2nd switch once again.
2nd mode is automatically canceled when the ignition switch is turned off.
The driving test should be performed on a paved road (nonskid road).
Start the engine.
Turn the ECT 2nd switch off (normal drive mode).
Confirm vehicle response by driving from a parked position to fully depressing the accelerator pedal.
Turn the ECT 2nd switch on and perform the same check as above.
When driving the vehicle with the ECT 2nd switch on and off, check that there is a difference in acceleration.
There is a difference in acceleration.
OK
NG
w/ Entry and Start System:
Remove the integration control and panel assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH(w/ Entry and Start System)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 8 (2ND) - 5 (E) | ECT 2nd switch on | Below 1 Ω |
| 8 (2ND) - 5 (E) | ECT 2nd switch off | 10 kΩ or higher |
| *a | Component without harness connected
(Integration Control and Panel Assembly) |
w/o Entry and Start System:
Remove the suspension control switch (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH(w/o Entry and Start System)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 17 (2ND) - 20 (E) | ECT 2nd switch on | Below 1 Ω |
| 17 (2ND) - 20 (E) | ECT 2nd switch off | 10 kΩ or higher |
| *a | Component without harness connected
(Suspension Control Switch) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Entry and Start System) | B |
| NG (w/o Entry and Start System) | C |
A
B
C
w/ Entry and Start System:
Disconnect the integration control and panel assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V9-5 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Integration Control and Panel Assembly) |
w/o Entry and Start System:
Disconnect the suspension control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V4-20 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Suspension Control Switch) |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A38-17 (SNWI) - Body ground | ECT 2nd switch on | Below 1 Ω |
| A38-17 (SNWI) - Body ground | ECT 2nd switch off | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A52-17 (SNWI) - Body ground | ECT 2nd switch on | Below 1 Ω |
| A52-17 (SNWI) - Body ground | ECT 2nd switch off | 10 kΩ or higher |
| A | for LHD |
| B | for RHD |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG