Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER(w/o Entry and Start System)
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255266 SHIFT LEVER(w/o Entry and Start System) G

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER(w/o Entry and Start System)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT SHIFT LEVER POSITION

a.

When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that it moves smoothly and correctly into position.


b.

Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.


c.

Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.

If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


Hide 2.CHECK SHIFT LOCK OPERATION

a.

Move the shift lever to P.


b.

Turn the ignition switch off.


c.

Check that the shift lever cannot be moved from P.


d.

Turn the ignition switch to ON, depress the brake pedal and check that the shift lever can be moved to other positions.

If the operation cannot be done as specified, inspect the shift lever assembly and shift lock control unit.


Hide 3.CHECK SHIFT LOCK RELEASE BUTTON OPERATION

a.

When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position.

If the operation cannot be performed as specified, check the shift lever assembly.


Hide 85903 4.CHECK SHIFT LOCK CONTROL ECU

C113154E09
1.026,1.864 0.798,0.963 false 1.033,2.341 0.825,2.911 false 0.399,0.753 0.749,0.950 0.350,0.198 10 STP 0.691,3.01 0.937,3.179 0.246,0.170 10 IG 2.032,0.753 2.243,0.928 0.211,0.175 10 E 1.863,1.858 2.019,0.979 false 0.378,0 2.686,0.430 2.308,0.430 10 Component with harness connected: (Shift Lock Control ECU)

a.

Measure the voltage according to the values in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard Voltage:
Tester Connection Condition Specified Condition
12 (IG) - 3 (E) Ignition switch ON 11 to 14 V
12 (IG) - 3 (E) Ignition switch off Below 1 V
6 (STP) - 3 (E) Depress brake pedal 11 to 14 V
6 (STP) - 3 (E) Release brake pedal Below 1 V



b.
C113154E10
1.856,1.047 1.856,1.912 false 1.803,0.842 2.014,1.017 0.211,0.175 10 E 0.305,0.023 2.636,0.385 2.331,0.362 10 Component with harness connected: (Shift Lock Control ECU)

Measure the resistance according to the value in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard Resistance:
Tester Connection Condition Specified Value
3 (E) - Body ground Always Below 1 Ω



c.
C172429E01
0.199,0.073 2.707,0.458 2.508,0.385 10 Component without harness connected: (Shift Lock Control ECU) 2.34,1.849 2.569,1.18 false 1.927,1.849 1.697,1.18 false 2.618,0.996 3.038,1.184 0.420,0.188 10 SLS+ 1.232,0.996 1.607,1.184 0.375,0.188 10 SLS-

Disconnect the shift lock solenoid connector from the shift lock control ECU.


d.

Measure the voltage according to the values in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.


Standard Voltage:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Ignition switch off Below 1 V
1 (SLS+) - 2 (SLS-) Ignition switch ON Below 1 V
Ignition switch ON and brake pedal depressed 11 to 14 V


If the result is not as specified, replace the shift lever assembly.


Hide 85431 5.CHECK SHIFT LOCK SOLENOID

C150404E07
1.155,2.022 1.277,2.188 0.122,0.167 10 1 1.501,2.022 1.623,2.188 0.122,0.167 10 2 1.841,2.022 1.963,2.188 0.122,0.167 10 3 2.195,2.022 2.317,2.188 0.122,0.167 10 4 0.21,0 2.792,0.372 2.582,0.372 10 Component without harness connected: (Shift Lock Solenoid) 1.687,0.863 2.051,1.065 0.364,0.202 10 SLS- 0.673,0.863 1.097,1.065 0.424,0.202 10 SLS+ 1.223,1.956 1.07,1.08 false 1.54,1.956 1.692,1.08 false 1.891,2.216 1.785,2.821 false 2.207,2.216 2.313,2.821 false 2.305,2.854 2.453,3.027 0.148,0.173 10 P 1.623,2.854 1.854,3.027 0.231,0.173 10 E2

a.

Disconnect the shift lock solenoid connector from the shift lock control ECU.


b.

Measure the resistance according to the values in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 101 to 123 Ω
3 (E2) - 4 (P) Shift lever in P 10 kΩ or higher
3 (E2) - 4 (P) Shift lever not in P Below 1 Ω



c.

Apply 12 V battery voltage to the shift lock solenoid and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Terminal 1 (SLS+)

·

Battery negative (-) → Terminal 2 (SLS-)


Solenoid moves and makes an operating noise


If the result is not as specified, replace the shift lever assembly.