Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255271 AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) L

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)  PRECAUTION  


NOTICE:
·

Perform the Reset Memory procedures (A/T initialization) after replacing the automatic transmission assembly, valve body assembly or any of the shift solenoid valves (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)>INITIALIZATION).

HINT:

Reset Memory cannot be completed by only reconnecting the cable to the negative (-) battery terminal.


·

If either of the following conditions is met, perform ATF Thermal Degradation Estimate Reset (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)>INITIALIZATION).

-

The ATF has been replaced.

-

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.




CAUTION:

When using compressed air, always aim away from yourself to prevent Automatic Transmission Fluid (ATF) or kerosene from spraying on your face.


NOTICE:
·

The automatic transmission is composed of precision-made parts, necessitating careful inspection before reassembly because even a small nick could cause fluid leakage or affect performance.

·

The procedures are organized so that you work on only one component group at a time. This will help avoid confusion with similar-looking parts of different sub-assemblies being on your workbench at the same time.

·

The component groups are inspected and repaired from the converter housing side.

·

Whenever possible, complete the inspection, repair and reassembly before proceeding to the next component group. If a defect is found in a certain component group during reassembly, inspect and repair this group immediately. If a component group cannot be assembled because parts are being ordered, be sure to keep all parts of the group in a separate container while proceeding with disassembly, inspection, repair and reassembly of other component groups.

·

Use of Toyota Genuine ATF WS is recommended.

·

All disassembled parts should be washed clean, and compressed air should be blown through any fluid passages and holes.

·

Dry all parts with compressed air. Never use a cloth.

·

The recommended ATF or kerosene should be used for cleaning.

·

After cleaning, the parts should be arranged in the order they were removed for efficient inspection, repairs, and reassembly.

·

New discs for the brakes and clutches that will be used for replacement must be soaked in ATF for at least 15 minutes before reassembly.

·

All oil seal rings, clutch discs, clutch plates, rotating parts and sliding surfaces should be coated with ATF prior to reassembly.

·

All old gaskets and rubber O-rings must be replaced.

·

Do not apply adhesive cement to gaskets and similar parts.

·

Make sure that the ends of the snap rings are not aligned with any cutouts. Also make sure that snap rings are correctly installed into the grooves.

·

If a worn bushing is to be replaced, the sub-assembly containing the bushing must also be replaced.

·

Check the thrust bearings and races for wear or damage. Replace them if necessary.

·

Use petroleum jelly to keep parts in place.

·

When working with FIPG material, perform the following:

Using a razor blade and gasket scraper, remove all old FIPG material from the gasket surface.

Clean all components thoroughly to remove all foreign matter.

Clean both sealing surfaces with a non-residue solvent.

Apply FIPG material in a continuous line on the sealing surface.

Reassemble parts within 10 minutes of applying FIPG material. Failing to do so will require the FIPG material to be removed and reapplied.