Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255271 AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)  Pattern Select Switch Power Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and power shift patterns and lock-up pattern.

By following the programs corresponding to the signals from the pattern select switch, the park/neutral position switch and other various sensors, the ECM switches the shift solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM

C179561E15
2.139,2.647 2.663,2.842 0.524,0.195 10 V4 2.139,2.825 3.862,3.021 1.723,0.195 10 Suspension Control Switch 3.528,1.198 3.672,1.393 0.144,0.195 10 P 3.351,2.134 3.674,2.329 0.323,0.195 10 2ND 2.389,2.134 2.533,2.329 0.144,0.195 10 E 3.719,1.429 4.439,1.624 0.719,0.195 10 3 3.719,2.362 4.367,2.557 0.647,0.195 10 4 2.117,2.362 2.393,2.557 0.276,0.195 10 16 5.22,1.429 5.406,1.624 0.186,0.195 10 51 5.517,1.313 5.921,1.508 0.404,0.195 10 PWR 5.301,2.362 5.487,2.557 0.186,0.195 10 4 5.517,2.245 5.976,2.440 0.459,0.195 10 SNWI 5.659,3.231 6.041,3.427 0.382,0.196 10 ECM 5.659,3.043 6.102,3.245 0.443,0.202 10 A38

CAUTION / NOTICE / HINT

When the pattern select (PWR) switch is pushed, switch contact is made and power mode is selected. To cancel power mode, push the pattern select (2nd) switch once again.

PROCEDURE

1.INSPECT PATTERN SELECT (PWR) SWITCH
a.
C238423E09
2.365,1.762 2.778,1.964 0.413,0.202 10 P 0.049,0 0.245,0.202 0.195,0.202 10 *a 2.443,1.743 2.058,1.082 false 1.236,1.762 1.473,1.964 0.237,0.202 10 E 1.328,1.743 1.63,1.286 false

Remove the suspension control switch (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (P) - 16 (E) Pattern select (PWR) switch on Below 1 Ω
3 (P) - 16 (E) Pattern select (PWR) switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Suspension Control Switch)



OK

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)

NG

REPLACE PATTERN SELECT (PWR) SWITCH (SUSPENSION CONTROL SWITCH)

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)
a.
U165081E01
1.931,1.704 1.799,1.389 false 1.889,1.704 2.163,1.906 0.274,0.202 10 E 0.057,0.005 0.252,0.207 0.195,0.202 10 *a 0.334,0.979 0.709,1.212 0.375,0.233 10 V4

Disconnect the suspension control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-16 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Suspension Control Switch)



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)
U164936E01
0.058,0.002 0.375,0.204 0.317,0.202 10 *a 1.621,0.22 1.996,0.453 0.375,0.233 10 A38 1.114,1.782 1.789,1.983 0.676,0.202 10 51 (PWR) 1.509,1.756 1.657,1.287 false

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-51 (PWR) - Body ground Pattern select (PWR) switch on Below 1 Ω
A38-51 (PWR) - Body ground Pattern select (PWR) switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR