Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255273 AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to S using the transmission control switch, it is possible to switch the shift range between "1" (1st range) and "6" (6th range).

Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM

C176192E29
5.642,1.183 5.872,1.353 0.230,0.170 10 25 3.943,2.149 4.410,2.345 0.467,0.195 10 SFTD 3.943,1.562 4.410,1.757 0.467,0.195 10 SFTU 4.215,0.972 4.344,1.167 0.129,0.195 10 S 3.059,0.972 3.299,1.167 0.240,0.195 10 IG 3.059,2.149 3.299,2.345 0.240,0.195 10 E 5.964,1.09 6.386,1.285 0.422,0.195 10 S 5.642,1.771 5.872,1.941 0.230,0.170 10 38 5.964,1.678 6.386,1.874 0.422,0.195 10 SFTU 5.642,2.361 5.872,2.530 0.230,0.170 10 27 5.964,2.267 6.386,2.462 0.422,0.195 10 SFTD 2.797,2.732 3.219,2.927 0.422,0.195 10 E52 2.797,2.912 4.575,3.107 1.779,0.195 10 Transmission Control Switch 0.357,1.07 2.323,1.265 1.966,0.195 10 from ECU-IG NO. 2 Fuse 2.854,1.196 3.021,1.366 0.167,0.170 10 3 2.854,2.372 3.045,2.541 0.191,0.170 10 5 4.395,1.196 4.757,1.366 0.362,0.170 10 7 4.395,1.785 4.678,1.954 0.283,0.170 10 2 4.395,2.372 4.713,2.541 0.318,0.170 10 1 0.087,2.968 0.878,3.170 0.791,0.202 10 *1: for LHD 0.087,3.342 0.878,3.544 0.791,0.202 10 *2: for RHD 6.073,3.413 6.455,3.608 0.382,0.196 10 ECM 6.073,3.015 6.516,3.217 0.443,0.202 10 A38*1 6.073,3.201 6.516,3.403 0.443,0.202 10 A52*2

PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E44
1.615,0.75 1.021,0.365 false 1.823,0.76 2.427,0.427 false 1.021,1.365 1.625,0.969 false 1.927,0.99 2.417,1.271 false 1.958,0.802 2.365,0.802 false 0.104,0.052 0.417,0.25 0.313,0.198 10 false *a 0.823,0.26 1.063,0.458 0.24,0.198 10 false IG 0.854,1.302 1.042,1.5 0.188,0.198 10 false S 2.49,0.323 2.99,0.51 0.5,0.188 10 false SFTU 2.458,1.198 2.958,1.385 0.5,0.188 10 false E 2.458,0.708 2.958,0.896 0.5,0.188 10 false SFTD

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
2 (SFTU) - 5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever in S 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever in S 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)
a.
U164958E01
0.057,0.004 0.374,0.206 0.317,0.202 10 *a 1.815,1.141 2.019,1.666 false 1.995,1.666 2.311,1.868 0.316,0.202 10 IG 1.294,1.688 1.484,1.343 false 1.179,1.666 1.495,1.868 0.316,0.202 10 E 0.626,0.961 1.001,1.194 0.375,0.233 10 E52

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
E52-3 (IG) - Body ground Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-5 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)


OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U164943E02
1.042,1.667 1.979,0.99 false 1.813,1.688 2.125,0.99 false 2.615,1.688 2.115,1.188 false 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.698,1.688 1.146,1.885 0.448,0.198 10 false 25 (S) 1.354,1.698 2.073,1.896 0.719,0.198 10 false 27 (SFTD) 2.354,1.708 3.073,1.906 0.719,0.198 10 false 38 (SFTU) 1.219,0.292 1.594,0.521 0.375,0.229 10 false A38 1.615,0.24 1.813,0.469 0.198,0.229 10 false *1 2,0.302 2.375,0.531 0.375,0.229 10 false A52 2.417,0.24 2.615,0.469 0.198,0.229 10 false *2

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A38-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever in S, "+" or "-"


11 to 14 V
A38-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever not in S, "+" or "-"


Below 1 V

for RHD
Tester Connection Condition Specified Condition
A52-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever in S, "+" or "-"


11 to 14 V
A52-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever not in S, "+" or "-"


Below 1 V



c.

Turn the engine switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-38 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A38-27 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A38-38 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
A38-27 (SFTD) - Body ground Shift lever in S 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-38 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A52-27 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A52-38 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
A52-27 (SFTD) - Body ground Shift lever in S 10 kΩ or higher



Text in Illustration
*1 for LHD
*2 for RHD
*a Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR