Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255273 AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

C221301E01
4.885,2.063 5.208,1.125 5.208,1.125 5.271,1.125 true 5.031,2.208 5.188,2.573 5.188,2.573 5.26,2.573 true 5.875,2.271 6,2.573 6,2.573 6.063,2.573 true 6.115,2.479 7,2.698 0.885,0.219 10 false Solenoid Coil 0.104,0.677 1.354,0.896 1.25,0.219 10 false Hydraulic Pressure 2.563,3.01 3.125,3.229 0.563,0.219 10 false Current 5.313,2.49 5.844,2.708 0.531,0.219 10 false Sleeve 5.323,1.031 6.167,1.25 0.844,0.219 10 false Spool Valve

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve.

Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC Code DTC Detection Condition Trouble Area
P2716 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic)
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C178085E42
2.792,0.927 3.021,1.094 0.229,0.167 10 false 13 0.813,0.969 1.042,1.135 0.229,0.167 10 false 2 0.813,1.802 1.042,1.969 0.229,0.167 10 false 1 5.51,0.917 5.74,1.083 0.229,0.167 10 false 9 2.323,0.698 2.75,0.896 0.427,0.198 10 false SLT+ 2.813,2.156 3.042,2.323 0.229,0.167 10 false 5 2.323,1.906 2.75,2.104 0.427,0.198 10 false SLT- 5.781,0.781 6.208,0.979 0.427,0.198 10 false SLT+ 5.521,2.156 5.75,2.323 0.229,0.167 10 false 8 5.781,2 6.208,2.198 0.427,0.198 10 false SLT- 1.031,2.51 1.458,2.708 0.427,0.198 10 false C34 1.031,2.667 2.646,2.865 1.615,0.198 10 false No. 1 Transmission Wire 1.031,1.365 2.677,1.594 1.646,0.229 10 false Shift Solenoid Valve SLT 5.917,2.979 6.396,3.146 0.479,0.167 10 false C46*2 5.917,2.823 6.396,2.99 0.479,0.167 10 false C45*1 5.917,3.135 6.344,3.333 0.427,0.198 10 false ECM 0.104,3 0.906,3.198 0.802,0.198 10 false *1: for LHD 0.104,3.375 0.906,3.573 0.802,0.198 10 false *2: for RHD

PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C214326E38
1.571,1.306 1.371,1.745 false 1.676,1.087 1.93,1.745 false 1.134,1.783 1.498,1.950 0.363,0.167 10 SLT+ 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 1.79,1.783 2.133,1.950 0.343,0.167 10 SLT-

Disconnect the No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLT+) - 5 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLT+) - Body ground Always 10 kΩ or higher
5 (SLT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(No. 1 Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
U165053E02
0.792,1.719 1.208,0.844 false 1.26,0.844 1.75,1.729 false 0.094,0.021 0.385,0.229 0.292,0.208 10 false *a 0.458,1.75 1.177,1.948 0.719,0.198 10 false 8 (SLT-) 1.417,1.75 2.125,1.948 0.708,0.198 10 false 9 (SLT+) 0.948,0.281 1.323,0.51 0.375,0.229 10 false C45 1.354,0.229 1.531,0.458 0.177,0.229 10 false *1 1.792,0.281 2.167,0.51 0.375,0.229 10 false C46 2.198,0.229 2.375,0.458 0.177,0.229 10 false *2

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-9 (SLT+) - C45-8 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C45-9 (SLT+) - Body ground Always 10 kΩ or higher
C45-8 (SLT-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-9 (SLT+) - C46-8 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C46-9 (SLT+) - Body ground Always 10 kΩ or higher
C46-8 (SLT-) - Body ground Always 10 kΩ or higher



Text in Illustration
*1 for LHD
*2 for RHD
*a Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR