Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255273 AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)  Pattern Select Switch Power Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and power shift patterns and lock-up pattern.

By following the programs corresponding to the signals from the pattern select switch, the park/neutral position switch and other various sensors, the ECM switches the solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM

C179561E12
2.139,2.649 2.663,2.844 0.524,0.195 10 V4 2.139,2.827 3.862,3.022 1.723,0.195 10 Suspension Control Switch 3.528,1.199 3.672,1.395 0.144,0.195 10 P 3.351,2.135 3.674,2.330 0.323,0.195 10 2ND 2.389,2.135 2.533,2.330 0.144,0.195 10 E 3.719,1.43 4.356,1.626 0.637,0.195 10 3*3, 16*4 3.719,2.363 4.363,2.558 0.644,0.195 10 4*3, 17*4 1.63,2.363 2.326,2.558 0.696,0.195 10 16*3, 20*4 5.22,1.43 5.406,1.626 0.186,0.195 10 51 5.517,1.315 5.921,1.510 0.404,0.195 10 PWR 5.3,2.363 5.486,2.559 0.186,0.195 10 4 5.517,2.247 5.976,2.442 0.459,0.195 10 SNWI 0.045,3.096 1.022,3.271 0.977,0.174 10 *3: w/ CRAWL 0.045,3.42 1.140,3.595 1.095,0.174 10 *4: w/o CRAWL 0.045,2.448 0.840,2.623 0.795,0.174 10 *1: for LHD 0.045,2.772 0.840,2.947 0.795,0.174 10 *2: for RHD 5.659,3.418 6.041,3.614 0.382,0.196 10 ECM 5.659,3.044 6.102,3.246 0.443,0.202 10 A38*1 5.659,3.231 6.102,3.433 0.443,0.202 10 A52*2

CAUTION / NOTICE / HINT

When the pattern select (PWR) switch is pushed, switch contact is made and power mode is selected. To cancel power mode, push the pattern select (PWR) switch once again.

PROCEDURE

1.INSPECT PATTERN SELECT (PWR) SWITCH
a.
C238423E05
2.365,1.762 2.778,1.964 0.413,0.202 10 P*A 0.049,0 0.245,0.202 0.195,0.202 10 *a 2.443,1.743 2.058,1.082 false 1.163,1.762 1.779,1.964 0.616,0.202 10 E*A, P*B 1.499,1.743 1.63,1.286 false 0.548,1.762 0.844,1.964 0.295,0.202 10 E*B 0.76,1.743 1.053,1.286 false

Remove the suspension control switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ CRAWL
Tester Connection Switch Condition Specified Condition
3 (P) - 16 (E) Pattern select (PWR) switch on Below 1 Ω
3 (P) - 16 (E) Pattern select (PWR) switch off 10 kΩ or higher

w/o CRAWL
Tester Connection Switch Condition Specified Condition
16 (P) - 20 (E) Pattern select (PWR) switch on Below 1 Ω
16 (P) - 20 (E) Pattern select (PWR) switch off 10 kΩ or higher


Text in Illustration
A w/ CRAWL
B w/o CRAWL
*a Component without harness connected
(Suspension Control Switch)



OK

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)

NG

REPLACE PATTERN SELECT (PWR) SWITCH (SUSPENSION CONTROL SWITCH)

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)
a.
U165080E01
2.519,1.704 2.376,1.389 false 2.421,1.704 2.695,1.906 0.274,0.202 10 E*B 1.663,1.704 1.799,1.389 false 1.475,1.704 1.749,1.906 0.274,0.202 10 E*A 0.057,0.005 0.252,0.207 0.195,0.202 10 *a 0.334,0.979 0.709,1.212 0.375,0.233 10 V4

Disconnect the suspension control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ CRAWL
Tester Connection Condition Specified Condition
V4-16 (E) - Body ground Always Below 1 Ω

w/o CRAWL
Tester Connection Condition Specified Condition
V4-20 (E) - Body ground Always Below 1 Ω


Text in Illustration
A w/ CRAWL
B w/o CRAWL
*a Front view of wire harness connector
(to Suspension Control Switch)



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)
U164944E01
0.058,0.002 0.375,0.204 0.317,0.202 10 *a 1.377,1.782 2.053,1.983 0.676,0.202 10 51 (PWR) 1.772,1.756 1.657,1.289 false 1.118,0.209 1.493,0.442 0.375,0.233 10 A38 1.534,0.209 1.727,0.442 0.193,0.233 10 *1 1.921,0.209 2.296,0.442 0.375,0.233 10 A52 2.338,0.209 2.531,0.442 0.193,0.233 10 *2

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
A38-51 (PWR) - Body ground Pattern select (PWR) switch on Below 1 Ω
A38-51 (PWR) - Body ground Pattern select (PWR) switch off 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
A52-51 (PWR) - Body ground Pattern select (PWR) switch on Below 1 Ω
A52-51 (PWR) - Body ground Pattern select (PWR) switch off 10 kΩ or higher



Text in Illustration
*1 for LHD
*2 for RHD
*a Front view of wire harness connector
(to ECM)


OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR