Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255273 AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)  Pattern Select Switch Power Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and power shift patterns and lock-up pattern.

By following the programs corresponding to the signals from the PWR switch (integration control and panel assembly), the park/neutral position switch and other various sensors, the ECM switches the solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM

C344742E04
2.339,2.83 4.893,3.022 2.554,0.192 10 Integration Control and Panel Assembly 2.339,2.644 2.634,2.845 0.295,0.201 10 V9 3.723,1.432 3.916,1.633 0.193,0.201 10 6 3.522,1.194 3.715,1.395 0.193,0.201 10 P 3.723,2.367 3.916,2.567 0.193,0.201 10 8 3.334,2.128 3.721,2.329 0.387,0.201 10 2ND 2.388,2.13 2.775,2.331 0.387,0.201 10 E 2.194,2.367 2.387,2.567 0.193,0.201 10 5 5.491,1.308 6.268,1.508 0.776,0.201 10 PWR 5.491,2.237 6.268,2.438 0.776,0.201 10 SNWI 5.291,2.367 5.540,2.567 0.248,0.201 10 4 5.219,1.432 5.486,1.633 0.267,0.201 10 51 5.638,3.02 6.400,3.221 0.762,0.201 10 A38*1 5.671,3.404 6.105,3.605 0.434,0.201 10 ECM 0.099,4.147 1.470,4.348 1.371,0.201 10 *1: for LHD 5.638,3.206 6.400,3.407 0.762,0.201 10 A52*2 0.099,4.399 1.283,4.600 1.184,0.201 10 *2: for RHD

CAUTION / NOTICE / HINT

When the PWR switch is pushed, switch contact is made and power mode is selected. To cancel power mode, push the PWR switch once again.

PROCEDURE

1.INSPECT PWR SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.
C331266E17
2.198,1.396 2.729,1.521 false 0.677,1.031 1.208,1.146 false 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2.792,1.458 3.021,1.646 0.229,0.188 10 false P 0.49,0.896 0.719,1.083 0.229,0.188 10 false E

Remove the integration control and panel assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH(w/ Entry and Start System)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (P) - 5 (E) PWR switch on Below 1 Ω
6 (P) - 5 (E) PWR switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Integration Control and Panel Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - BODY GROUND)
a.
U165552E01
0.375,0.802 0.663,1.035 0.288,0.233 10 V9 2.407,1.683 2.703,1.885 0.295,0.202 10 E 2.4,1.664 2.011,1.06 false 0.097,0.02 0.393,0.222 0.295,0.202 10 *a

Disconnect the integration control and panel assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-5 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Integration Control and Panel Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL AND PANEL ASSEMBLY - ECM)
U164944E01
0.058,0.002 0.375,0.204 0.317,0.202 10 *a 1.377,1.782 2.053,1.983 0.676,0.202 10 51 (PWR) 1.772,1.756 1.657,1.289 false 1.118,0.209 1.493,0.442 0.375,0.233 10 A38 1.534,0.209 1.727,0.442 0.193,0.233 10 *1 1.921,0.209 2.296,0.442 0.375,0.233 10 A52 2.338,0.209 2.531,0.442 0.193,0.233 10 *2

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
A38-51 (PWR) - Body ground PWR switch on Below 1 Ω
A38-51 (PWR) - Body ground PWR switch off 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
A52-51 (PWR) - Body ground PWR switch on Below 1 Ω
A52-51 (PWR) - Body ground PWR switch off 10 kΩ or higher



Text in Illustration
*1 for LHD
*2 for RHD
*a Front view of wire harness connector
(to ECM)


OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR