Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255274 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) D

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF)  HYDRAULIC TEST  


PERFORM HYDRAULIC TEST


a.

Measure the line pressure.

CAUTION:

The line pressure test should always be carried out in pairs. One technician should observe the conditions of the wheels and wheel chocks outside the vehicle while the other is performing the test.


NOTICE:
·

Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).

·

Be careful to prevent SST hose from interfering with the exhaust pipe.

·

This check must be conducted after checking and adjusting the engine.

·

Perform the test with the A/C turned off.

·

When conducting the stall test, do not continue for more than 5 seconds.



HINT:

The measured values may not fall within the specified range depending on the measurement environment.


i.

Warm up the ATF (Automatic Transmission Fluid).


ii.

Turn the engine switch off.


iii.

Lift the vehicle up.


iv.
C161166E01
2.116,0.715 2.458,0.905 0.342,0.190 10 SST 2.446,0.517 2.287,0.694 false 0.288,3.989 0.953,4.174 0.666,0.185 10 Test Plug 1.578,3.742 1.107,4.074 1.107,4.074 1.045,4.074 false 0.123,1.731 0.464,1.922 0.342,0.190 10 SST 0.384,1.406 0.294,1.711 false

Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095  (09992-00231, 09992-00271)


v.

Lower the vehicle.


vi.

Fully apply the parking brake and chock the 4 wheels.


vii.

Start the engine and check the idling speed.


viii.

Keep your left foot pressed firmly on the brake pedal and move the shift lever to D.


ix.

Fully depress the accelerator pedal with your right foot. Quickly read the highest line pressure when the engine speed reaches the stall speed.


x.

In the same manner, perform the test with the shift lever in R.

Specified Line Pressure
Condition D Position kPa (kgf/cm2, psi) R Position kPa (kgf/cm2, psi)
Stall speed 1230 to 1590 kPa
(12.5 to 16.2 kgf/cm2, 178 to 231 psi)
1470 to 1800 kPa
(15.0 to 18.4 kgf/cm2, 213 to 261 psi)

Evaluation
Problem Possible Cause
Measured values at D and R positions are higher than specified pressure
·

Shift solenoid valve SLT defective

·

Regulator valve defective


Measured values at D and R positions are lower than specified pressure
·

Shift solenoid valve SLT defective

·

Regulator valve defective

·

Oil pump defective


Pressure is low in D position only
·

D position circuit fluid leak

·

Clutch No. 1 (C1) defective


Pressure is low in R position only
·

R position circuit fluid leak

·

Clutch No. 3 (C3) defective

·

Brake No. 4 (B4) defective