Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255274 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF)  Pattern Select Switch Power Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and power shift patterns and lock-up pattern.

By following the programs corresponding to the signals from the PWR switch, the park/neutral position switch and other various sensors, the ECM switches the solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM

C344742E01
2.339,2.81 4.893,3.002 2.554,0.192 10 Integration Control and Panel Assembly 2.339,2.624 2.634,2.825 0.295,0.201 10 V9 3.723,1.432 3.916,1.633 0.193,0.201 10 6 3.522,1.194 3.715,1.395 0.193,0.201 10 P 3.723,2.367 3.916,2.567 0.193,0.201 10 8 3.334,2.128 3.721,2.329 0.387,0.201 10 2ND 2.388,2.13 2.775,2.331 0.387,0.201 10 E 2.194,2.367 2.387,2.567 0.193,0.201 10 5 5.491,1.308 6.268,1.508 0.776,0.201 10 PWR 5.491,2.237 6.268,2.438 0.776,0.201 10 SNWI 5.212,2.367 5.461,2.567 0.248,0.201 10 17 5.219,1.432 5.486,1.633 0.267,0.201 10 21 5.697,3.02 6.085,3.221 0.387,0.201 10 A38 5.691,3.206 6.125,3.407 0.434,0.201 10 ECM 0.079,0.014 0.937,0.215 0.857,0.201 12 for LHD:

C344742E02
2.339,2.818 5.004,3.011 2.665,0.192 10 Integration Control and Panel Assembly*1 2.339,2.633 2.634,2.834 0.295,0.201 10 V9 3.723,1.441 4.477,1.642 0.753,0.201 10 6*1, 16*2 3.522,1.203 3.715,1.404 0.193,0.201 10 P 3.723,2.375 4.440,2.576 0.716,0.201 10 8*1, 17*2 3.334,2.137 3.721,2.338 0.387,0.201 10 2ND 2.388,2.138 2.775,2.339 0.387,0.201 10 E 1.698,2.375 2.307,2.576 0.610,0.201 10 5*1, 20*2 5.491,1.316 6.268,1.517 0.776,0.201 10 PWR 5.491,2.246 6.268,2.447 0.776,0.201 10 SNWI 5.212,2.375 5.461,2.576 0.248,0.201 10 17 5.219,1.441 5.486,1.642 0.267,0.201 10 21 5.697,3.029 6.085,3.230 0.387,0.201 10 A52 5.691,3.214 6.125,3.415 0.434,0.201 10 ECM 0.079,0.023 1.062,0.224 0.982,0.201 12 for RHD: 2.339,3.32 4.275,3.512 1.936,0.192 10 Suspension Control Switch*2 2.339,3.134 2.634,3.335 0.295,0.201 10 V4 0.082,4.039 2.018,4.231 1.936,0.192 10 *1: w/ Entry and Start System 0.082,4.373 2.130,4.565 2.047,0.192 10 *2: w/o Entry and Start System

CAUTION / NOTICE / HINT

When the PWR switch is pushed, switch contact is made and power mode is selected. To cancel power mode, push the PWR switch once again.

PROCEDURE

1.INSPECT PWR SWITCH
a.
C331266E10
2.352,1.835 2.538,2.037 0.186,0.202 10 P 2.368,1.835 2.152,1.414 false 0.808,1.835 1.104,2.037 0.295,0.202 10 E 0.892,1.835 1.282,1.183 false 0.097,0.02 0.393,0.222 0.295,0.202 10 *a

w/ Entry and Start System:

Remove the integration control and panel assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH(w/ Entry and Start System)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (P) - 5 (E) PWR switch on Below 1 Ω
6 (P) - 5 (E) PWR switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Integration Control and Panel Assembly)


c.
C238423E13
0.049,0 0.245,0.202 0.195,0.202 10 *a 1.723,1.762 2.339,1.964 0.616,0.202 10 P 1.742,1.743 1.63,1.286 false 0.816,1.762 1.112,1.964 0.295,0.202 10 E 0.93,1.743 1.053,1.286 false

w/o Entry and Start System:

Remove the suspension control switch (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH(w/o Entry and Start System)>REMOVAL).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
16 (P) - 20 (E) PWR switch on Below 1 Ω
16 (P) - 20 (E) PWR switch off 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Suspension Control Switch)

Result
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C


A

2.CHECK HARNESS AND CONNECTOR (PWR SWITCH - BODY GROUND)

B

C

2.CHECK HARNESS AND CONNECTOR (PWR SWITCH - BODY GROUND)
a.
U165549E01
0.375,0.802 0.663,1.035 0.288,0.233 10 V9 2.407,1.683 2.703,1.885 0.295,0.202 10 E 2.4,1.664 2.011,1.06 false 0.097,0.02 0.393,0.222 0.295,0.202 10 *a

w/ Entry and Start System:

Disconnect the integration control and panel assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-5 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Integration Control and Panel Assembly)


c.
U165082E01
2.519,1.704 2.376,1.389 false 2.494,1.704 2.768,1.906 0.274,0.202 10 E 0.057,0.005 0.252,0.207 0.195,0.202 10 *a 0.334,0.979 0.709,1.212 0.375,0.233 10 V4

w/o Entry and Start System:

Disconnect the suspension control switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-20 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Suspension Control Switch)


OK

3.CHECK HARNESS AND CONNECTOR (PWR SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PWR SWITCH - ECM)
a.
U164950E01
0.058,0.002 0.375,0.204 0.317,0.202 10 *a 1.125,0.22 1.414,0.453 0.288,0.233 10 A38 1.522,0.22 1.722,0.453 0.199,0.233 10 *A 1.953,0.22 2.242,0.453 0.288,0.233 10 A52 2.35,0.22 2.550,0.453 0.199,0.233 10 *B 1.743,1.741 2.419,1.943 0.676,0.202 10 21 (PWR) 1.972,1.716 1.657,0.944 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
A38-21 (PWR) - Body ground PWR switch on Below 1 Ω
A38-21 (PWR) - Body ground PWR switch off 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
A52-21 (PWR) - Body ground PWR switch on Below 1 Ω
A52-21 (PWR) - Body ground PWR switch off 10 kΩ or higher



Text in Illustration
A for LHD
B for RHD
*a Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR