Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION FLUID › 2015.08–2017.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255279 AUTOMATIC TRANSMISSION FLUID N

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  ADJUSTMENT  


PROCEDURE

Hide 1.BEFORE FILLING TRANSMISSION

·

The A750F automatic transmission assembly requires Toyota Genuine ATF WS.

·

If the entire automatic transmission assembly, automatic transmission oil pan sub-assembly, drain plug, transmission valve body assembly and/or torque converter assembly have/has been replaced, proceed to the Fill Transmission procedure.

·

If the transmission case adapter rear oil seal has been replaced and/or an automatic transmission fluid leak has been replaced, proceed to the Adjust Fluid Temperature procedure.


Hide 2. TRANSMISSION PAN WITH FLUID

a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.
C419316E01
2.219,2.125 2.375,2.125 2.375,2.125 2.521,1.031 true 2.656,2.469 2.854,2.469 2.854,2.469 3.052,1.25 true 0.74,4.25 0.74,4.052 0.74,4.052 1.542,3.688 true 1.531,2.042 2.26,2.302 0.729,0.26 10 false Refill Hole 1.958,2.375 2.677,2.667 0.719,0.292 10 false Refill Plug 0.365,4.26 1.438,4.542 1.073,0.281 10 false Overflow Plug

Using a 5 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transmission assembly.


c.

Remove the refill plug and O-ring from the automatic transmission assembly.


d.

Add automatic transmission fluid to the refill hole until it flows out of the overflow hole.

C419313E01
1.531,0.458 1.823,0.458 1.823,0.458 2.385,1.271 true 4.396,2.229 4.635,2.229 4.635,2.229 5.302,1.552 true 0.854,0.365 1.531,0.615 0.677,0.25 10 false Refill Hole 3.51,2.135 4.396,2.396 0.885,0.26 10 false Overflow Hole

NOTICE:
·

Use Toyota Genuine ATF WS.

·

Be sure to add automatic transmission fluid slowly. If automatic transmission fluid is added quickly, the automatic transmission fluid may hit internal parts and bounce back, resulting in automatic transmission fluid coming out of the refill hole.




e.

Wait until the automatic transmission fluid flow slows and only drips come out.

C419314


f.

Using a 5 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the automatic transmission assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again.



Hide 3. TRANSMISSION FILL

a.

Fill the transmission with the amount of fluid listed in the table below.

Standard Capacity:
Repair Fill Amount
Transmission pan and drain plug removal 1.7 liters (1.8 US qts, 1.5 Imp. qts)
Transmission valve body removal 4.3 liters (4.5 US qts, 3.8 Imp. qts)
Torque converter removal 5.4 liters (5.7 US qts, 4.8 Imp. qts)


HINT:

If the specified amount of automatic transmission fluid cannot be added, perform the following:


i.

Temporarily install the O-ring and refill plug to the automatic transmission assembly.

HINT:

Reuse the old O-ring as the refill plug will be removed again.



ii.

Lower the vehicle.


iii.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.



iv.

Slowly move the shift lever from P to D, then move the shift lever to P.


v.

Allow the engine to idle for 30 seconds to warm it up.


vi.

Turn the engine switch off.


vii.

Remove the refill plug and O-ring from the automatic transmission assembly.


viii.

Fill the automatic transmission assembly with the correct amount of automatic transmission fluid as listed in the table above.


ix.

Temporarily install the O-ring and refill plug to the automatic transmission assembly.

HINT:

Reuse the old O-ring as the refill plug will be removed again.




Hide 4.ADJUST FLUID TEMPERATURE

NOTICE:

The fluid temperature can be confirmed by checking the indicator light in the meter or by using the GTS. When using the GTS, it is necessary to change to temperature detection mode in order to idle the vehicle appropriately.


a.

When using the GTS:

i.

Turn the engine switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the engine switch on (IG).


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.


v.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.


vi.

Check the ATF temperature.

NOTICE:
·

The ATF temperature must be between 38 to 45°C (100 to 113°F).

·

If the ATF temperature is not between 38 to 45°C (100 to 113°F), turn the engine switch off and wait until the fluid temperature drops between 38 to 45°C (100 to 113°F).




vii.

According to the display on the GTS, perform the Active Test "Connect the TC and TE1".

HINT:

Indicator lights of the meter blink to output DTCs when TC and TE1 are connected.



viii.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.




b.
H102392E90
2.039,0.34 2.272,0.490 0.234,0.150 10 CG 2.165,1.765 2.379,1.925 0.214,0.160 10 TC 0.108,0.052 1.437,0.289 1.329,0.237 10 Front view of DLC3: 2.022,0.49 1.616,0.891 false 1.777,1.451 2.123,1.798 false

When not using the GTS:

i.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.


HINT:

Indicator lights of the meter blink to output DTCs when terminals TC and CG are connected.




c.

Slowly move the shift lever from P to S, and then move the shift lever to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transmission.



d.
C337023

Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.

Standard condition:

Indicator light (D) remains illuminated for 2 seconds and then turns off.



e.

When using the GTS:

i.

Return the shift lever to P and press OFF on the Active Test display.



f.

When not using the GTS:

i.

Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).



g.

Allow the engine to idle until the fluid temperature reaches 38 to 45°C (100 to 113°F).


h.

The indicator (D) will come on again when the fluid temperature reaches 38°C (100°F) and will blink when it exceeds 46°C (113°F).

Indicator Indication of ATF Temperature:
Below Proper Temperature Proper Temperature Higher than Proper Temperature
Data List [A/T Oil Temperature 1]
38°C (100°F) or less
Data List [A/T Oil Temperature 1]
38 to 45°C (100 to 113°F)
Data List [A/T Oil Temperature 1]
45°C (113°F) or higher
Indicator light (D)
Turns off
Indicator light (D)
Turns on
Indicator light (D)
Blinking


NOTICE:

Perform the fluid level inspection while the indicator light is on.



Hide 5.CHECK FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.
C419317

Using a 5 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transmission assembly.

CAUTION:

Be careful as the automatic transmission fluid coming out of the overflow hole is hot.



c.

Check the amount of automatic transmission fluid that comes out of the overflow hole.

·

If the amount of automatic transmission fluid that comes out of the overflow hole is large, proceed to step [*1].

·

If no automatic transmission fluid comes out of the overflow hole, proceed to step [*2].


NOTICE:

If only a small amount of automatic transmission fluid (approximately 5 cc) comes out of the overflow hole, then only automatic transmission fluid remaining in the No. 1 transmission oil filler tube has come out. This is not considered to be overflow.



d.

If the amount of automatic transmission fluid that comes out of the overflow hole is large, wait until the automatic transmission fluid flow slows and only drips come out. [*1]

C419314

HINT:

The automatic transmission fluid flow will not stop completely because the automatic transmission fluid continues to expand as its temperature increases.



e.

If no automatic transmission fluid comes out of the overflow hole, remove the refill plug and O-ring. Then add automatic transmission fluid to the refill hole until it flows out of the overflow hole. [*2]

C419313E01
1.531,0.458 1.823,0.458 1.823,0.458 2.385,1.271 true 4.396,2.229 4.635,2.229 4.635,2.229 5.302,1.552 true 0.854,0.365 1.531,0.615 0.677,0.25 10 false Refill Hole 3.51,2.135 4.396,2.396 0.885,0.26 10 false Overflow Hole

NOTICE:
·

Use Toyota Genuine ATF WS.

·

Be sure to add automatic transmission fluid slowly. If automatic transmission fluid is added quickly, the automatic transmission fluid may hit internal parts and bounce back, resulting in automatic transmission fluid coming out of the refill hole.




f.

Wait until the automatic transmission fluid flow slows and only drips come out.

C419314

HINT:

The automatic transmission fluid flow will not stop completely because the automatic transmission fluid continues to expand as its temperature increases.



g.

Using a 5 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transmission assembly.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


h.
C419318

Install a new O-ring and the refill plug to the automatic transmission assembly.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


i.

Lower the vehicle.


j.

Turn the engine switch off.

HINT:

Turning the engine switch off exits automatic transmission fluid temperature detection mode.



k.

Disconnect the GTS from the DLC3 (when using the GTS).


Hide 6. AFTER FILLING TRANSMISSION

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for automatic transmission fluid leaks.


d.

Lower the vehicle.


Hide 7. ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.

Click hereDrivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>INITIALIZATION