Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION UNIT › 2014.08–2017.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255287 AUTOMATIC TRANSMISSION UNIT A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C171522E01
1.61,0.8 1.747,0.969 0.136,0.169 10 A 2.861,2.037 2.998,2.198 0.137,0.161 10 B 3.48,3.292 3.631,3.459 0.152,0.167 10 C 4.721,3.064 4.853,3.230 0.133,0.166 10 D 4.83,1.424 4.976,1.582 0.146,0.158 10 E 5.825,4.257 5.978,4.463 0.153,0.205 10 F 4.656,4.461 4.803,4.634 0.147,0.173 10 G 1.881,6.713 2.026,6.881 0.145,0.168 10 H 4.432,7.517 4.511,7.688 0.079,0.172 10 I 4.38,6.05 4.501,6.229 0.121,0.179 10 J

Bearing and Race Diameter:
Mark Front Race Diameter Inside/Outside Thrust Bearing Diameter Inside/Outside Rear Race Diameter Inside/Outside
A 74.3 to 74.6 mm (2.93 to 2.94 in.)/87.4 to 87.7 mm (3.44 to 3.45 in.) 72.0 to 72.3 mm (2.83 to 2.85 in.)/85.3 to 85.6 mm (3.36 to 3.37 in.) -
B 37.0 to 37.3 mm (1.46 to 1.47 in.)/52.1 to 52.3 mm (2.05 to 2.06 in.) 34.7 to 34.9 mm (1.366 to 1.374 in.)/51.6 to 51.9 mm (2.03 to 2.04 in.) -
C - 21.4 to 21.6 mm (0.841 to 0.850 in.)/40.8 to 41.0 mm (1.606 to 1.614 in.) 22.7 to 22.9 mm (0.892 to 0.902 in.)/60.0 to 60.4 mm (2.36 to 2.38 in.)
D 33.3 to 33.5 mm (1.31 to 1.32 in.)/56.3 to 56.6 mm (2.22 to 2.23 in.) 38.5 to 38.7 mm (1.515 to 1.524 in.)/56.5 to 57.0 mm (2.22 to 2.24 in.) -
E - 42.6 to 42.8 mm (1.68 to 1.69 in.)/60.8 to 61.1 mm (2.39 to 2.41 in.) -
F 38.0 to 38.2 mm (1.496 to 1.504 in.)/56.5 to 57.0 mm (2.22 to 2.24 in.) 43.4 to 43.6 mm (1.71 to 1.72 in.)/58.0 to 58.4 mm (2.28 to 2.30 in.) -
G - 55.8 to 56.0 mm (2.197 to 2.204 in.)/76.1 to 76.4 mm (2.996 to 3.008 in.) 53.8 to 54.0 mm (2.12 to 2.13 in.)/73.7 to 74.0 mm (2.90 to 2.91 in.)
H 33.4 to 33.6 mm (1.31 to 1.32 in.)/48.7 to 49.0 mm (1.92 to 1.93 in.) 32.2 to 32.3 mm (1.268 to 1.272 in.)/49.0 to 49.2 mm (1.93 to 1.94 in.) 32.2 to 32.4 mm (1.27 to 1.28 in.)/48.7 to 49.0 mm (1.92 to 1.93 in.)
I - 21.5 to 21.8 mm (0.846 to 0.858 in.)/40.5 to 40.8 mm (1.59 to 1.61 in.) -
J - 43.6 to 43.9 mm (1.72 to 1.73 in.)/60.6 to 60.9 mm (2.39 to 2.40 in.) 47.2 to 47.4 mm (1.86 to 1.87 in.)/66.9 to 67.1 mm (2.63 to 2.64 in.)


Hide 35629A 2.ASSEMBLE NO. 4 BRAKE PISTON AND BRAKE REACTION SLEEVE

D028795E16
1.031,1.458 1.906,1.823 1.906,1.823 1.635,1.469 false 2.24,1.021 2.271,1.708 2.271,1.708 2.729,0.938 false 2,1.74 2.823,1.927 0.823,0.188 10 false New O-Ring

a.

Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.


b.

Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.


c.

Install the No. 4 brake piston to the reaction sleeve.


Hide 35626 3.INSTALL NO. 4 BRAKE PISTON WITH BRAKE REACTION SLEEVE

D028080

a.

Install the No. 4 brake piston with brake reaction sleeve to the transmission case

NOTICE:
·

Do not damage the O-rings.

·

Make sure the No. 4 brake piston is underneath the brake reaction sleeve.




Hide 35623H 4.INSTALL 1ST AND REVERSE BRAKE PISTON

D028081

a.

Coat a new O-ring with ATF.


b.

Install the O-ring to the 1st and reverse brake piston.


c.

With the spring seat of the piston facing upwards (the front side), place the piston in the transmission case.

NOTICE:

Be careful not to damage the O-ring.



d.
D028549

Place the brake return spring onto the 1st and reverse brake piston.


Hide 35068 5.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
D028082E05
0.906,0.344 1.01,0.344 1.01,0.344 0.969,0.99 false 1.615,0.281 1.51,0.281 1.51,0.281 1.521,0.781 false 0.208,0.24 0.885,0.469 0.677,0.229 10 false Snap Ring 1.677,0.198 2.021,0.396 0.344,0.198 10 false SST

Place SST on a new spring retainer, and compress the return spring.

SST
09350-30020  (09350-07050)


b.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


Hide 35719B 6.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.
U116383

Install the No. 9 thrust bearing race.

Thrust Bearing Race Diameter:
Item Inside Outside
No. 9 Race 47.2 to 47.4 mm (1.86 to 1.87 in.) 66.9 to 67.1 mm (2.63 to 2.64 in.)



b.
D027946E09
0.479,1.594 0.615,0.271 0.615,0.271 0.771,0.271 false 2.667,1.656 2.792,1.656 2.792,1.656 3.094,0.573 false 0.854,0.188 1.552,0.385 0.698,0.198 10 false Bearing I 2.021,1.573 2.719,1.771 0.698,0.198 10 false Bearing J

Coat the 2 thrust needle roller bearings with petroleum jelly, and install them to the rear planetary gear.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Bearing J 43.6 to 43.9 mm (1.72 to 1.73 in.) 60.6 to 60.9 mm (2.39 to 2.40 in.)
Bearing I 21.5 to 21.8 mm (0.846 to 0.858 in.) 40.5 to 40.8 mm (1.59 to 1.61 in.)



c.
D027945

Install the rear planetary gear assembly.


Hide 7.INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

a.
D027966

Make sure the 1st and reverse brake piston moves smoothly when applying and releasing compressed air into the transmission case.


b.
D224349E01
1.396,0.781 1.552,0.979 0.156,0.198 10 false A

Using a vernier caliper, measure the level difference (length A) between the upper surface of the 1st and reverse brake piston and the hitting surface of the No. 4 brake flange at both ends across a diameter, and calculate the average.

NOTICE:

The 1st and reverse brake piston must be installed tightly to the end face of the transmission case.


HINT:

Length A = 36.35 to 37.09 mm (1.43 to 1.46 in.)



c.
U150412E03
2.26,0.365 2.646,0.365 false 1.979,0.417 2.656,0.417 false 2.573,0.698 2.563,0.177 false 0.781,0.906 0.938,1.104 0.156,0.198 10 false B 2.729,0.313 2.885,0.51 0.156,0.198 10 false H

Using a vernier caliper, measure the thickness (length B) of the 2 brake flanges, 7 No. 4 brake plates and 8 No. 4 brake discs all together at both ends across a diameter, and calculate the average.

HINT:

Pack clearance = Length A - Length B - 0.25 mm to 1.8 mm (0.00984 to 0.0709 in.)

Length B = 36.04 to 37.14 mm (1.42 to 1.46 in.)


Standard pack clearance:

0.8 to 1.1 mm (0.0315 to 0.0433 in.)


If the pack clearance is outside the standard, select and install a brake flange that makes the pack clearance within the standard.

H Thickness:
No. Thickness
0 0 mm (0 in.)
2 0.15 to 0.25 mm (0.00590 to 0.00984 in.)
4 0.35 to 0.45 mm (0.0138 to 0.0177 in.)
6 0.55 to 0.65 mm (0.0217 to 0.0256 in.)
8 0.75 to 0.85 mm (0.0295 to 0.0335 in.)
10 0.95 to 1.05 mm (0.0374 to 0.0413 in.)
12 1.15 to 1.25 mm (0.0453 to 0.0492 in.)
14 1.35 to 1.45 mm (0.0531 to 0.0571 in.)



Hide 35684 8.INSTALL NO. 4 BRAKE DISC

a.
U152678

Install the 2 flanges, 8 discs and 7 plates.

Install in order:

F - D - P - D - P - D - P - D - P - D - P - D - P - D - P - D - F


HINT:

F = Flange

D = Disc

P = Plate



Hide 35639B 9.INSTALL BRAKE PLATE STOPPER SPRING

D027943

Hide 35077D 10.INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

a.
D027965E25
1.135,1.083 1.083,0.323 1.083,0.323 0.917,0.323 false 1.563,0.948 1.594,0.281 1.594,0.281 1.729,0.281 false 0.177,0.219 0.958,0.458 0.781,0.24 10 false No. 7 Race 1.813,0.219 2.594,0.458 0.781,0.24 10 false No. 8 Race

Install the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and planetary ring gear flange to the intermediate shaft.

Thrust Needle Roller Bearing and Race Diameter:
Item Inside Outside
No. 7 Race 33.4 to 33.6 mm (1.31 to 1.32 in.) 48.7 to 49.0 mm (1.92 to 1.93 in.)
Bearing 32.2 to 32.3 mm (1.268 to 1.272 in.) 49.0 to 49.2 mm (1.93 to 1.94 in.)
No. 8 Race 32.2 to 32.4 mm (1.27 to 1.28 in.) 48.7 to 49.0 mm (1.92 to 1.93 in.)



Hide 35770C 11.INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY

a.
D027964

Install the 1-way clutch and 1-way clutch inner race to the intermediate shaft.


Hide 35713 12.INSTALL INTERMEDIATE SHAFT

a.
D027942

Install the intermediate shaft with No. 3 1-way clutch assembly to the case.


b.
D027927E17
1.406,0.292 0.698,0.292 false 0.385,0.208 0.813,0.5 0.427,0.292 10 true SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 35750 13.INSTALL CENTER PLANETARY GEAR ASSEMBLY

a.
D027940

Install the planetary sun gear and center planetary gear to the case.


b.

Coat the No. 6 thrust bearing race with petroleum jelly, and install it to the center planetary gear.

Thrust Bearing Race Diameter:
Item Inside Outside
Race 53.8 to 54.0 mm (2.12 to 2.13 in.) 73.7 to 74.0 mm (2.90 to 2.91 in.)



Hide 35622G 14.INSTALL NO. 2 BRAKE PISTON

a.
D028797E18
1.073,0.635 1.01,0.125 false 0.708,1.479 1.01,0.125 1.01,0.125 1.146,0.125 false 1.188,0.052 2.063,0.333 0.875,0.281 10 true New O-Ring

Coat 2 new O-rings with ATF, and install them to the brake piston.


b.

Press the brake piston into the brake cylinder with both hands.

NOTICE:

Be careful not to damage the O-rings.



c.

Install the No. 2 brake piston to the case.


Hide 35682A 15.INSTALL NO. 2 BRAKE DISC

D027938

a.

Install the brake piston return spring.


b.

Install the 3 plates, 3 discs and flange.

Install in order:

D - P - D - P - D - P - F


HINT:

D = Disc

P = Plate

F = Flange



c.
D028818E15
2.094,0.542 2.833,0.542 false 1.854,1.115 2.813,0.542 false 2.854,0.469 3.292,0.75 0.438,0.281 10 true SST

Using SST and a press, compress the return spring and install the No. 2 brake spring snap ring.

SST
09351-40010  


Hide 35621V 16.INSTALL NO. 1 BRAKE PISTON

a.
U152680E03
1.417,0.708 1.281,0.135 false 1.49,0.063 2.344,0.333 0.854,0.271 10 true New O-Ring

Coat 2 new O-rings with ATF, and install them to the brake piston.


b.

Press the brake piston into the brake cylinder with both hands.

NOTICE:

Be careful not to damage the O-rings.



Hide 35608J 17.INSTALL BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
D027935

Install the brake piston return spring and the No. 1 brake piston with No. 1 brake cylinder to the transmission case.


Hide 35608K 18.INSTALL BRAKE PISTON RETURN SPRING SNAP RING

a.
D028819E10
1.563,0.802 0.448,1.323 false 1.615,1.323 0.458,1.323 false 0.125,1.25 0.531,1.49 0.406,0.24 10 false SST

Using SST and a press, compress the return spring and install the brake piston return spring snap ring.

SST
09351-40010  


Hide 35681A 19.INSTALL NO. 1 BRAKE DISC

D027933

a.

Install the 3 plates, 3 discs and flange.

Install in order:

P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange



Hide 35763 20.INSTALL CENTER PLANETARY RING GEAR

a.
D028541

Install the center planetary ring gear and front planetary ring gear flange to the front planetary ring gear.


b.
D028540

Using a screwdriver, install the snap ring.


Hide 35743 21.INSTALL FRONT PLANETARY RING GEAR

a.
D027932

Install the front planetary ring gear and thrust needle roller bearing to the case.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Bearing 55.8 to 56.0 mm (2.197 to 2.204 in.) 76.1 to 76.4 mm (2.996 to 3.008 in.)



Hide 35720 22.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
D027931E26
0.833,0.26 1.042,0.26 false 0.833,0.948 1.042,0.948 false 1.094,0.188 1.542,0.479 0.448,0.292 10 true Race 1.104,0.875 1.698,1.146 0.594,0.271 10 true Bearing

Install the thrust washer and thrust needle roller bearing.


b.

Coat the No. 5 thrust race with petroleum jelly, and install it to the front planetary ring gear.

Thrust Needle Roller Bearing and Race Diameter:
Item Inside Outside
Bearing 43.4 to 43.6 mm (1.71 to 1.72 in.) 58.0 to 58.4 mm (2.28 to 2.30 in.)
Race 38.0 to 38.2 mm (1.496 to 1.504 in.) 56.5 to 57.0 mm (2.22 to 2.24 in.)



c.
D027930

Install the front planetary gear assembly and 1-way clutch inner race to the case.


Hide 23.INSPECT PISTON STROKE OF NO. 1 BRAKE PISTON

a.
D028814

Make sure the No. 1 brake piston moves smoothly when applying and releasing compressed air into the transmission case.


b.
D028815E01
2.993,0 3.414,0.08 0.421,0.08

Using a feeler gauge, measure the B3 brake pack clearance between the snap ring and flange.

Standard piston stroke:

0.42 to 0.72 mm (0.0165 to 0.0283 in.)


If the piston stroke is outside the specification, parts may have been assembled incorrectly. Perform the reassembly again. If the piston stroke is still outside the specification, select another flange.

HINT:

There are 4 different thicknesses for the flange.


Flange Thickness:
Mark Thickness
0 1.95 to 2.05 mm (0.0768 to 0.0807 in.)
1 2.15 to 2.25 mm (0.0846 to 0.0886 in.)
2 2.35 to 2.45 mm (0.0925 to 0.0965 in.)
3 2.55 to 2.65 mm (0.100 to 0.104 in.)



Hide 35624 24.INSTALL 2ND BRAKE PISTON

a.
D028546E22
1.177,0.802 1.021,0.125 false 1.135,0.125 1.021,0.125 1.021,0.125 0.635,1.26 false 1.208,0.052 2.031,0.406 0.823,0.354 10 true New O-Ring

Coat 2 new O-rings with ATF, and install them to the 2nd brake piston.


b.

Press the 2nd brake cylinder into the 2nd brake piston with both hands.

NOTICE:

Be careful not to damage the O-rings.



c.
D028817E13
2.646,0.365 2.906,0.198 false 2.969,0.115 3.333,0.292 0.365,0.177 10 false SST

Using SST and a press, compress the return spring and install the snap ring.

SST
09351-40010  

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35664 25.INSTALL 2ND BRAKE CYLINDER

a.
D027929

Install the 2nd brake cylinder to the case.


Hide 35790 26.INSTALL 1-WAY CLUTCH ASSEMBLY

a.
D027928

Install the thrust washer and 1-way clutch to the case.


Hide 35624J 27.INSTALL 2ND BRAKE PISTON HOLE SNAP RING

a.
D027927E17
1.406,0.292 0.698,0.292 false 0.385,0.208 0.813,0.5 0.427,0.292 10 true SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 28.INSTALL NO. 3 BRAKE DISC

a.
D027926

Install the cushion plate, 4 plates, 4 discs and flange to the case.

Install in order:

C - P - D - P - D - P - D - P - D - F


HINT:

C = Cushion plate

P = Plate

D = Disc

F = Flange



Hide 35679C 29.INSTALL NO. 3 BRAKE SNAP RING

a.
D027925

Using a screwdriver, install the snap ring.


Hide 35606A 30.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
D028816E12
2.083,1.365 2.313,1.771 2.313,1.771 2.563,1.333 false 1.896,1.823 2.698,2.021 0.802,0.198 10 false New O-Ring

Coat 2 new O-rings with ATF, and install them to the direct clutch piston.


b.
D028517

Install the No. 2 clutch balancer and direct clutch return spring to the direct clutch piston.


c.
D028516E04
1.083,1.781 1.365,1.865 false 1.385,1.792 2.208,2.01 0.823,0.219 10 false New O-Ring

Coat a new O-ring with ATF, and install it to the clutch drum.


d.

Press the direct clutch piston into the clutch drum with both hands.

NOTICE:

Be careful not to damage the O-rings.



e.
D028514E13
0.521,1.396 1.26,0.708 false 0.521,1.396 1.469,1.396 false 0.219,1.333 0.563,1.531 0.344,0.198 10 false SST

Place SST on the direct clutch piston, and compress the return spring with a press.

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring sheet from being deformed.


SST
09320-89010  
09350-30020  (09350-07070)


f.

Install the snap ring with a snap ring expander.

NOTICE:

Do not expand the snap ring excessively.



g.
D028536E19
1.219,1.01 1.74,1.427 1.74,1.427 2.219,1 false 1.51,1.406 2.021,1.74 0.51,0.333 10 true Stopper

Set the end gap of the snap ring in the piston as shown in the illustration

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35048 31.INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

a.
D028513E11
1.188,1.792 1.365,1.854 false 1.406,1.802 2.208,2.01 0.802,0.208 10 false New O-Ring

Coat a new O-ring with ATF, and install it to the clutch drum.


b.
D028512E11
2.208,0.354 1.74,0.219 false 0.958,0.115 1.771,0.344 0.813,0.229 10 false New O-Ring

Coat a new O-ring with ATF, and install it to the reverse clutch piston.


c.
D028511

Press the clutch drum into the reverse clutch piston with both hands.

NOTICE:

Be careful not to damage the O-ring.



Hide 35047 32.INSTALL REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
D028510E17
1.323,0.656 1.052,0.448 false 0.281,0.323 1.115,0.531 0.833,0.208 10 false New O-Ring

Coat a new O-ring with ATF, and install it to the reverse clutch piston.


b.

Install the reverse clutch return spring to the reverse clutch piston.


Hide 35688 33.INSTALL NO. 3 CLUTCH BALANCER

a.
D028509E12
1.688,0.938 2.281,0.51 2.281,0.51 2.188,0.896 false 2.333,0.406 2.792,0.604 0.458,0.198 10 false SST

Place SST on the No. 3 clutch balancer, and compress the clutch balancer with a press.

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.


SST
09387-00070  
09350-30020  (09350-07070)


b.

Install the snap ring with a snap ring expander.

NOTICE:

Do not expand the snap ring excessively.



c.
D028534E07
0.729,0.51 0.792,1.031 0.792,1.031 0.854,1.031 false 0.896,0.958 1.302,1.135 0.406,0.177 10 false Gap

Set the end gap of the snap ring in the piston as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35667A 34.INSTALL DIRECT CLUTCH DISC

C162137E01
1.021,0.651 1.148,0.821 0.128,0.171 10 F 1.021,1.069 1.148,1.240 0.128,0.171 10 P 1.021,0.888 1.148,1.059 0.128,0.171 10 D 1.021,1.436 1.148,1.607 0.128,0.171 10 P 1.021,1.255 1.148,1.426 0.128,0.171 10 D 1.021,1.805 1.148,1.976 0.128,0.171 10 P 1.021,1.614 1.148,1.785 0.128,0.171 10 D 1.021,2.184 1.148,2.355 0.128,0.171 10 P 1.021,1.983 1.148,2.154 0.128,0.171 10 D 1.021,2.553 1.148,2.724 0.128,0.171 10 P 1.021,2.362 1.148,2.533 0.128,0.171 10 D 1.28,0.739 1.16,0.739 false 1.302,0.965 1.171,0.965 false 1.307,1.15 1.171,1.15 false 1.306,1.335 1.171,1.335 false 1.307,1.531 1.171,1.531 false 1.305,1.7 1.171,1.7 false 1.306,1.891 1.171,1.891 false 1.306,2.063 1.171,2.063 false 1.307,2.267 1.171,2.267 false 1.307,2.444 1.171,2.444 false 1.307,2.635 1.171,2.635 false

a.

Install the 5 plates, 5 discs and reverse clutch flange to the clutch drum.

Install in order:

P - D - P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange



b.
D028507

Using a screwdriver, install the 2 hole snap rings to the clutch drum.


Hide 35649 36.INSTALL REVERSE CLUTCH FLANGE

a.
D028506

Install the reverse clutch flange to the clutch drum.


Hide 35659 37.INSTALL REVERSE CLUTCH REACTION SLEEVE

D224350E01
1.76,0.375 2.125,0.375 false 1.729,0.875 2.094,0.875 false 1.729,1.115 2.104,1.115 false 0.708,1.292 1.073,1.292 false 0.708,1.5 1.073,1.5 false 0.708,1.698 1.073,1.698 false 0.708,1.896 1.073,1.896 false 0.719,2.104 1.083,2.104 false 0.719,2.302 1.083,2.302 false 0.729,2.5 1.094,2.5 false 0.729,2.698 1.094,2.698 false 0.729,2.906 1.094,2.906 false 0.542,1.219 0.698,1.417 0.156,0.198 10 false D 0.552,1.427 0.708,1.625 0.156,0.198 10 false P 2.208,0.302 2.365,0.5 0.156,0.198 10 false S 2.219,0.813 2.375,1.01 0.156,0.198 10 false C 2.229,1.063 2.385,1.26 0.156,0.198 10 false F 0.552,1.625 0.708,1.823 0.156,0.198 10 false D 0.552,1.833 0.708,2.031 0.156,0.198 10 false P 0.552,2.031 0.708,2.229 0.156,0.198 10 false D 0.552,2.229 0.708,2.427 0.156,0.198 10 false P 0.552,2.427 0.708,2.625 0.156,0.198 10 false D 0.552,2.635 0.708,2.833 0.156,0.198 10 false P 0.552,2.833 0.708,3.031 0.156,0.198 10 false D

a.

Install the 5 reverse clutch discs, 4 clutch plates, reverse clutch flange, clutch cushion plate and reverse clutch reaction sleeve to the reverse clutch hub.

Install in order:

D - P - D - P - D - P - D - P - D - F - C - S


HINT:

D = Disc

P = Plate

F = Flange

C = Cushion plate

S = Sleeve



b.

Using a screwdriver, install the hole snap ring.


Hide 35659 39.REMOVE REVERSE CLUTCH REACTION SLEEVE

a.
D029844

Using a screwdriver, remove the snap ring from the clutch drum.


b.
D029843

Remove the reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 5 reverse clutch discs, and 4 clutch plates from the reverse clutch hub.


Hide 35612B 40.INSTALL FORWARD CLUTCH PISTON

a.
D028525E05
0.604,1.438 1.125,0.156 false 2.271,0.313 1.125,0.146 false 1.125,0.146 1,0.146 false 0.229,0.063 1.073,0.302 0.844,0.24 10 false New O-Ring

Coat 2 new O-rings with ATF, and install them to the forward clutch piston.


Hide 35668 41.INSTALL NO. 1 CLUTCH BALANCER

a.
D028523E07
1.552,1.823 1.813,1.885 false 1.865,1.813 2.698,2.042 0.833,0.229 10 false New O-Ring

Coat a new O-ring with ATF and install it to the clutch balancer.


b.
D028522

Install the clutch balancer and forward clutch return spring.

NOTICE:

Be careful not to damage the O-ring.



c.
D028521E04
2.083,0.542 2.344,0.219 false 2.375,0.083 3.063,0.448 0.688,0.365 10 false SST

Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.


SST
09350-30020  (09350-07040, 09350-07070)


d.

Install the snap ring with a snap ring expander.

NOTICE:

Do not expand the snap ring excessively.



e.
D028535E05
0.656,1.063 0.521,0.792 false 0.229,0.688 0.563,0.875 0.333,0.188 10 false Gap

Set the end gap of the snap ring in the piston as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35633B 42.INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

D224351E01
2.125,0.469 2.531,0.469 false 2.125,0.792 2.531,0.792 false 2.115,1.094 2.521,1.094 false 2.115,1.427 2.521,1.427 false 2.125,1.74 2.531,1.74 false 2.125,2.021 2.531,2.021 false 0.99,0.302 1.396,0.302 false 0.99,0.604 1.396,0.604 false 0.99,0.938 1.396,0.938 false 0.99,1.25 1.396,1.25 false 0.99,1.563 1.396,1.563 false 0.99,1.885 1.396,1.885 false 1,2.188 1.406,2.188 false 0.792,0.229 0.948,0.427 0.156,0.198 10 false F 0.792,0.542 0.927,0.74 0.135,0.198 10 false P 2.615,0.385 2.75,0.583 0.135,0.198 10 false D 2.625,0.719 2.76,0.917 0.135,0.198 10 false D 2.625,1.021 2.76,1.219 0.135,0.198 10 false D 2.625,1.354 2.76,1.552 0.135,0.198 10 false D 2.625,1.667 2.76,1.865 0.135,0.198 10 false D 2.635,1.948 2.771,2.146 0.135,0.198 10 false D 0.802,2.115 0.958,2.313 0.156,0.198 10 false F 0.792,0.865 0.927,1.063 0.135,0.198 10 false P 0.792,1.188 0.927,1.385 0.135,0.198 10 false P 0.781,1.49 0.917,1.688 0.135,0.198 10 false P 0.792,1.813 0.927,2.01 0.135,0.198 10 false P

a.

Install the 2 flanges, 6 discs and 5 plates to the input shaft assembly.

Install in order:

F- D - P - D - P - D - P - D - P - D - P - D - F


HINT:

F = Flange

D = Disc

P = Plate



b.
D028519

Using a screwdriver, install the hole snap ring.


Hide 35712A 43.INSTALL INPUT SHAFT OIL SEAL RING

a.
D029677

Coat 3 new oil seal rings with ATF.


b.

Squeeze the ends of the 3 oil seal rings together, and then install them to the starter shaft groove.

NOTICE:

Do not excessively widen the ring.


HINT:

After installing the oil seal rings, check that they rotate smoothly.



Hide 35701 45.INSTALL INPUT SHAFT ASSEMBLY

a.
D028505

Install the input shaft to the clutch drum.


b.
D028504

Install the thrust needle roller bearing to the clutch drum.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Bearing 21.4 to 21.6 mm (0.841 to 0.850 in.) 40.8 to 41.0 mm (1.606 to 1.614 in.)



Hide 35631 46.INSTALL MULTIPLE DISC CLUTCH HUB

a.
D028503E11
3.01,0.49 3.073,0.135 3.073,0.135 2.948,0.135 false 0.51,1.833 0.49,1.938 0.49,1.938 0.625,1.938 false 0.698,1.865 1.469,2.042 0.771,0.177 10 false No. 4 Race 2.219,0.042 3.021,0.198 0.802,0.156 10 false No. 3 Race

Coat the 2 thrust bearing races with petroleum jelly, and install them onto the multiple disc clutch hub.

Thrust Bearing Race Diameter:
Item Inside Outside
No. 3 Race 22.7 to 22.9 mm (0.892 to 0.902 in.) 60.0 to 60.4 mm (2.36 to 2.38 in.)
No. 4 Race 33.3 to 33.5 mm (1.31 to 1.32 in.) 56.3 to 56.6 mm (2.22 to 2.23 in.)



b.
D028502

Install the multiple disc clutch hub to the clutch drum.


Hide 35061 47.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
D028500E09
3.042,1 3.042,1.365 false 0.344,1.177 0.344,0.667 0.344,0.667 0.49,0.667 false 0.531,0.583 1.323,0.844 0.792,0.26 10 false Bearing E 2.646,1.385 3.344,1.594 0.698,0.208 10 false Bearing D

Coat the 2 thrust needle roller bearings with petroleum jelly, and install them to the forward clutch hub.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Bearing D 38.5 to 38.7 mm (1.515 to 1.524 in.) 56.5 to 57.0 mm (2.22 to 2.24 in.)
Bearing E 42.6 to 42.8 mm (1.68 to 1.69 in.) 60.8 to 61.1 mm (2.39 to 2.41 in.)



b.
D028001

Install the forward clutch hub to the clutch drum.


Hide 35677C 48.INSTALL REAR CLUTCH DISC

a.
D027999E23
0.24,0.677 0.167,0.677 false 0.24,0.927 0.177,0.927 false 0.229,1.198 0.167,1.188 false 0.24,1.479 0.167,1.469 false 0.24,1.729 0.188,1.719 false 1.198,0.521 1.292,0.521 false 1.198,0.771 1.271,0.771 false 1.208,1.021 1.292,1.021 false 1.198,1.281 1.302,1.26 false 1.198,1.531 1.271,1.51 false 1.271,0.229 1.125,0.24 false 1.292,0.115 1.448,0.313 0.156,0.198 10 false C 1.302,0.375 1.49,0.583 0.188,0.208 10 false F 1.302,0.667 1.49,0.865 0.188,0.198 10 false P 0.052,0.594 0.25,0.792 0.198,0.198 10 false D 1.302,1.385 1.49,1.583 0.188,0.198 10 false P 1.313,1.135 1.5,1.333 0.188,0.198 10 false P 1.302,0.906 1.49,1.104 0.188,0.198 10 false P 0.063,1.625 0.26,1.823 0.198,0.198 10 false D 0.052,1.365 0.25,1.563 0.198,0.198 10 false D 0.042,1.094 0.24,1.292 0.198,0.198 10 false D 0.052,0.823 0.25,1.021 0.198,0.198 10 false D

Install the 5 discs, 4 plates, reverse clutch flange and clutch cushion plate to the reverse clutch hub.

Install in order:

D - P - D - P - D - P - D - P - D - F - C


HINT:

D = Disc

P = Plate

F = Flange

C = Cushion plate



Hide 35659 49.INSTALL REVERSE CLUTCH REACTION SLEEVE

a.
D027998

Install the reverse clutch reaction sleeve to the reverse clutch hub.


Hide 35049 50.INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY

a.
D027997

Install the reverse clutch hub to the clutch drum.


b.
D027996

Using a screwdriver, install the snap ring to the clutch drum and input shaft.


Hide 35780B 51.INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY

a.
D027994

Coat the No. 2 clutch drum thrust washer with petroleum jelly and install it to the clutch drum.


b.

Install the 1-way clutch to the clutch drum.


Hide 52.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

a.
C177432E05
0.292,1.146 0.49,0.219 0.49,0.219 0.656,0.219 false 0.74,1.531 0.802,1.833 0.802,1.833 0.969,1.833 false 0.729,0.146 1.448,0.354 0.719,0.208 10 false Bearing A 1.042,1.75 1.708,1.958 0.667,0.208 10 false Bearing B

Coat the 2 thrust needle roller bearings and clutch drum thrust washer with petroleum jelly and install them to the clutch drum and input shaft assembly.

Thrust Needle Roller Bearing Diameter:
Item Inside Outside
Bearing A 72.0 to 72.3 mm (2.83 to 2.85 in.) 85.3 to 85.6 mm (3.36 to 3.37 in.)
Bearing A 34.7 to 34.9 mm (1366 to 1.374 in.) 51.6 to 51.9 mm (2.03 to 2.04 in.)



b.
D029833

Install the clutch drum and input shaft assembly to the transmission case.


Hide 53.INSTALL OIL PUMP ASSEMBLY

a.
C177431E01
0.529,0.117 1.300,0.286 0.770,0.168 10 No. 1 Race 0.078,0.455 0.838,0.653 0.760,0.198 10 No. 2 Race 0.75,1.362 1.071,0.554 1.071,0.554 0.97,0.554 false 1.209,1.028 1.53,0.219 1.53,0.219 1.429,0.219 false

Coat the No. 1 and No. 2 thrust bearing races with petroleum jelly, and install them to the front oil pump.

Thrust Bearing Race Diameter:
Item Inside Outside
No. 1 Race 74.3 to 74.6 mm (2.93 to 2.94 in.) 87.4 to 87.7 mm (3.44 to 3.45 in.)
No. 2 Race 37.0 to 37.3 mm (1.46 to 1.47 in.) 52.1 to 52.3 mm (2.05 to 2.06 in.)



b.
D028796E07
1.948,0.313 1.625,0.156 false 0.854,0.052 1.677,0.302 0.823,0.25 10 false New O-Ring

Coat a new O-ring with ATF, and install it to the oil pump assembly.


c.

Place the oil pump through the input shaft, and align the bolt holes of the oil pump assembly with the transmission case.


d.

Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.

NOTICE:

Do not excessively push on the oil pump, as the oil seal ring will stick to the direct clutch drum.



e.
D027921

Install the 10 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 35506F 54.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
D028548E07
1.854,0.979 2.354,0.594 false 2.427,0.49 2.729,0.677 0.302,0.188 10 false SST

Using SST and hammer, tap in 2 new oil seals.

SST
09350-30020  (09350-07110)


b.

Coat the lip of the oil seals with MP grease.


Hide 35505 56.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

a.
D028798E07
1.042,0.99 0.917,0.292 0.917,0.292 0.688,0.292 false 0.698,1.042 0.49,1.333 false 0.156,1.333 0.969,1.698 0.813,0.365 10 false Manual Valve Lever 0.208,0.198 0.677,0.406 0.469,0.208 10 false Spacer

Install a new spacer to the manual valve lever.


b.

Push the manual valve lever shaft through the transmission case, and install the manual valve lever to the manual valve lever shaft.


c.
D028799

Using a hammer, tap in a new spring pin.


d.
D028800

Align the manual valve lever indentation with the spacer hole, and stake them together with a punch.


e.

Check that the shaft rotates smoothly.


Hide 35556 57.INSTALL PARKING LOCK PAWL SHAFT

a.
D028846E10
0.99,0.188 0.615,0.344 false 2.208,1.563 1.875,1.49 false 2.24,0.823 1.927,0.875 false 0.073,0.25 0.833,0.729 0.76,0.479 10 true Parking Lock Pawl 1.469,0.802 2,1.031 0.531,0.229 10 true E-Ring 1.417,1.375 2,1.615 0.583,0.24 10 true Spring

Install the E-ring to the shaft.


b.

Install the parking lock pawl, shaft and spring.


Hide 35501 58.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
D012709

Connect the parking lock rod to the manual valve lever.


Hide 35595 59.INSTALL PARKING LOCK PAWL BRACKET

a.
D012708

Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


b.
U152681E03
2.813,0.417 2.156,0.458 false 0.542,1.521 0.76,1.844 0.76,1.844 0.813,1.844 false 0.396,0.052 1.927,0.25 1.531,0.198 10 true Planetary Ring Gear 0.969,0.375 2.333,0.604 1.365,0.229 10 true Manual Valve Lever 0.865,1.75 1.552,1.958 0.688,0.208 10 true Lock Pawl

Move the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the lock pawl.


Hide 35424F 60.INSTALL C-1 ACCUMULATOR VALVE

a.
D028802E14
1.188,0.385 0.719,0.385 false 1,0.646 1.188,0.552 false 0.438,0.313 0.833,0.458 0.396,0.146 10 false C-1 0.229,0.573 1.031,0.802 0.802,0.229 10 false New O-Ring

Coat a new O-ring with ATF, and install it to the accumulator valve.


b.
D028803

Install the spring and accumulator valve to the hole.

Accumulator Spring Diameter:
Spring Free Length
Outer Diameter
Color
C-1 Inner 30.40 mm (1.20 in.)
11.40 mm (0.449 in.)
Pink
C-1 Outer 48.76 mm (1.92 in.)
16.60 mm (0.654 in.)
Light green



Hide 35426D 61.INSTALL C-3 ACCUMULATOR PISTON

a.
D028802E15
1.552,0.115 1.083,0.115 false 1.563,0.135 0.99,0.563 0.99,0.563 1.594,0.438 false 0.813,0.031 1.208,0.177 0.396,0.146 10 false C-3 0.198,0.49 0.99,0.719 0.792,0.229 10 false New O-Ring

Coat 2 new O-rings with ATF, and install them to the piston.


b.
D028804

Install the 2 springs and accumulator piston to the hole.

Accumulator Spring Diameter:
Spring Free Length
Outer Diameter
Color
C-3 Inner 44.0 mm (1.73 in.)
14.0 mm (0.551 in.)
Yellow
C-3 Outer 73.35 mm (2.89 in.)
19.90 mm (0.784 in.)
Red



Hide 35427K 62.INSTALL B-3 ACCUMULATOR PISTON

a.
D028802E16
2.26,0.115 2.813,0.115 false 1.979,0.583 1.021,0.552 1.021,0.552 1.938,0.24 false 2.875,0.042 3.146,0.229 0.271,0.188 10 false B-3 0.229,0.469 1.031,0.646 0.802,0.177 10 false New O-Ring

Coat 2 new O-rings with ATF, and install them to the piston.


b.
D028805

Install the spring and accumulator piston to the hole.

Accumulator Spring Diameter:
Spring Free Length
Outer Diameter
Color
B-3 70.5 mm (2.78 in.)
19.7 mm (0.776 in.)
Purple



Hide 35425A 63.INSTALL C-2 ACCUMULATOR PISTON

a.
D028802E17
2.615,0.26 2.74,0.26 false 2.313,0.313 1,0.635 1,0.635 2.344,0.604 false 2.802,0.188 3.083,0.365 0.281,0.177 10 false C-2 0.208,0.531 1.073,0.76 0.865,0.229 10 false New O-Ring

Coat 2 new O-rings with ATF, and install them to the piston.


b.
D028806

Install the spring and accumulator piston to the hole.

Accumulator Spring Diameter:
Spring Free Length
Outer Diameter
Color
C-2 62.0 mm (2.44 in.)
15.9 mm (0.626 in.)
White



Hide 35251 64.INSTALL CHECK BALL BODY

a.
C358295E01
0.969,0.458 1.292,0.458 false 0.823,1.24 1.51,1.229 false 0.25,0.365 0.969,0.729 0.719,0.365 10 false Check Ball Body 0.323,1.135 0.792,1.354 0.469,0.219 10 false Spring

Install the spring and check ball body.


Hide 35159 65.INSTALL BRAKE DRUM GASKET

a.
D027969

Install the 3 brake drum gaskets.


Hide 35145C 66.INSTALL TRANSMISSION CASE GASKET

a.
D027968E15
2.063,1.594 2.448,1.469 false 2.479,1.385 3.104,1.656 0.625,0.271 10 true Gasket

Install the 3 transmission case gaskets.


Hide 35410 67.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C157293E09
1.75,1.25 2.375,0.74 false 2.323,0.563 2.594,0.813 0.271,0.25 10 true Pin

Insert the pin of the manual valve into the hole of the manual valve lever.


b.
C157292E08
0.385,0.302 0.5,0.177 0.5,0.177 0.625,0.333 false 0.417,0.677 0.177,0.771 0.177,0.771 0.458,1.271 false 0.427,0.865 0.177,0.771 false 0.365,1.542 0.156,1.563 0.156,1.563 0.333,1.698 false 0.771,1.885 0.833,2.01 false 1.698,1.573 1.49,2.042 1.49,2.042 1.979,1.844 false 1.708,1.771 1.49,2.042 false 2.635,1.781 2.5,1.885 2.5,1.885 2.396,1.823 false 2.365,1.604 2.5,1.885 false 2.948,1.375 3.219,1.458 3.219,1.458 2.99,1.688 false 3.219,1.458 2.979,1.5 false 2.969,0.802 3.219,0.906 3.219,0.906 2.948,1 false 0.031,0.688 0.156,0.844 0.125,0.156 10 false A 0.031,1.479 0.167,1.656 0.135,0.177 10 false B 0.458,0.021 0.594,0.198 0.135,0.177 10 true B 1.354,2 1.49,2.177 0.135,0.177 10 true B 2.49,1.896 2.635,2.073 0.146,0.177 10 true B 3.25,1.375 3.385,1.552 0.135,0.177 10 false B 3.25,0.823 3.385,1 0.135,0.177 10 false B 0.792,1.969 0.958,2.177 0.167,0.208 10 true B

Install the transmission valve body assembly with the 19 bolts.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

36 mm (1.42 in.) for bolt A

25 mm (0.984 in.) for bolt B



c.

Install the detent spring and detent spring cover with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82125J 68.INSTALL TRANSMISSION WIRE

a.
D027912E01
3.007,0 3.414,0.108 0.407,0.108

Install a new O-ring to the transmission wire.


b.

Install the transmission wire harness.


c.

Install the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.
C125285E09
1.146,1.552 1.552,1.406 false 0.771,0.729 1.073,0.844 false 1.146,1.115 1.833,0.656 false 0.438,1.208 1.052,1.292 false 1.719,0.448 2.292,0.719 0.573,0.271 10 true Orange 0.104,1.115 0.531,1.313 0.427,0.198 10 true Blue 0.635,0.625 0.844,0.823 0.208,0.198 10 true A 1.573,1.302 1.74,1.521 0.167,0.219 10 true B

Connect the 7 solenoid connectors.


e.

Install the 2 ATF temperature sensors.


f.

Install the 2 clamps and 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

12 mm (0.472 in.) for bolt A

36 mm (1.42 in.) for bolt B


Sensor Wire Harness:
Wire Harness Color
No. 1 temperature sensor Orange
No. 2 temperature sensor Blue


Hide 35330 69.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
D012703

Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.


b.

Install the oil strainer with the 4 bolts.

Torque:
10 N*m (100 kgf*cm, 7 ft.*lbf)


Hide 35394 70.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
D027992E06
1.594,1.135 1.979,1.813 1.979,1.813 2.188,1.125 false 1.073,1.365 1.979,1.813 1.979,1.813 1.052,0.885 false 1.813,1.844 2.333,2.063 0.521,0.219 10 false Magnet

Install the 4 magnets.


Hide 35106 71.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.

Install a new gasket to the oil pan.


b.

Install the oil pan with the 20 bolts.

Torque:
4.4 N*m (45 kgf*cm, 39 in.*lbf)


c.

Install the drain plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35015E 72.INSTALL TRANSFER CASE ADAPTER RADIAL BALL BEARING

C162768E01
2.563,0.736 2.899,0.942 0.335,0.205 10 SST 2.534,0.902 1.865,1.183 false

a.

Using SST and a press, press in the bearing until it stops.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)


b.

Using a screwdriver, install the snap ring.


Hide 35015J 73.INSTALL TRANSMISSION CASE ADAPTER REAR OIL SEAL

C177436E07
1.208,1.052 0.406,1.188 false 0.115,1.115 0.438,1.281 0.323,0.167 10 false SST 2.354,1.135 3.188,1.344 0.833,0.208 10 false 0 to 0.5 mm

a.

Coat the lip of a new oil seal with ATF.


b.

Using SST and a hammer, tap in the oil seal.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)

Standard depth:

0 to 0.5 mm (0 to 0.0197 in.)



Hide 35015G 74.INSTALL TRANSFER ADAPTER REAR

a.

Clean the threads of the bolts and case.


b.
C175554E08
2.042,0.375 2.167,0.115 2.167,0.115 2.25,0.115 false 2.302,0.042 3.198,0.25 0.896,0.208 10 false Seal Packing 0.875,1.823 2.646,2.021 1.771,0.198 10 false Seal Diameter: 1 to 1.5 mm

Apply seal packing or equivalent to the transmission case adapter and 8 bolts.

Seal packing:

Toyota Genuine Seal Packing 1281,

Three Bond 1281 or equivalent


Seal diameter:

1.0 to 1.5 mm (0.0394 to 0.0591 in.)



c.
U152371E03
2.385,0.385 2.521,0.542 0.135,0.156 10 false A 2.469,1.25 2.604,1.406 0.135,0.156 10 false A 2.625,1.833 2.75,1.99 0.125,0.156 10 false B 2.073,1.885 2.198,2.042 0.125,0.156 10 false B 0.844,0.385 0.979,0.542 0.135,0.156 10 false A 0.76,1.25 0.896,1.406 0.135,0.156 10 false A 0.604,1.833 0.729,1.99 0.125,0.156 10 false B 1.167,1.885 1.292,2.042 0.125,0.156 10 false B

Install the transmission case adapter with the 8 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)

HINT:

Each bolt length is indicated below.

50 mm (1.97 in.) for bolt A

45 mm (1.77 in.) for bolt B



Hide 35111 75.INSTALL AUTOMATIC TRANSMISSION HOUSING

U148177E03
1.448,0.042 1.583,0.198 0.135,0.156 10 false A 2.052,0.052 2.188,0.208 0.135,0.156 10 false A 2.344,0.229 2.479,0.385 0.135,0.156 10 false A 1.156,0.188 1.292,0.344 0.135,0.156 10 false A 0.76,0.979 0.896,1.135 0.135,0.156 10 false A 2.667,1.052 2.802,1.208 0.135,0.156 10 false A 0.865,1.604 0.99,1.76 0.125,0.156 10 false B 2.51,1.667 2.635,1.823 0.125,0.156 10 false B 2.219,1.771 2.344,1.927 0.125,0.156 10 false C 1.167,1.74 1.292,1.896 0.125,0.156 10 false C

a.

Clean the threads of the bolts and case with non-residue solvent.


b.

Install the transmission housing with the 10 bolts.

Torque:
for 14 mm head bolt A : 34 N*m (345 kgf*cm, 25 ft.*lbf)
for 17 mm head bolt B : 57 N*m (581 kgf*cm, 42 ft.*lbf)
for 14 mm head bolt C : 34 N*m (345 kgf*cm, 25 ft.*lbf)


Hide 35122 76.INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE

U115758

a.

Coat a new O-ring with ATF and install it to the breather tube.


b.

Install the breather tube with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 89413B 77.INSTALL SPEED SENSOR

a.
C111258

Coat 2 new O-rings with ATF, and install them to the speed sensors.


b.

Install the 2 speed sensors.


c.

Install the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 32921C 78.INSTALL OIL COOLER TUBE UNION

a.

Coat 2 new O-rings with ATF, and install them to the 2 oil cooler tube unions.


b.
C250978

Using a union nut wrench, install the 2 oil cooler tube unions.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 84540 79.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903

a.

Install the park/neutral position switch to the manual valve lever shaft, and temporarily install the adjusting bolt.


b.

Install a new lock washer and the nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


c.
C172409E03
1.01,0.198 1.156,0.365 0.146,0.167 10 false P 1.76,0.042 1.906,0.208 0.146,0.167 10 false N 1.51,0.344 1.656,0.51 0.146,0.167 10 false R

Push the control shaft rearward as much as possible.


d.

Return the control shaft lever 2 notches to the N position.


e.
U152677E03
1.958,1.573 0.677,1.25 false 1.948,0.948 1.719,0.135 1.719,0.135 1.896,0.135 false 1.948,0.063 3.125,0.292 1.177,0.229 10 false Neutral Basic Line 0.208,1.146 0.74,1.344 0.531,0.198 10 false Groove

Align the neutral basic line with the switch groove as shown in the illustration, and tighten the adjusting bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


f.
D027990

Using a screwdriver, bend the tabs of the lock washer.

HINT:

Bend at least 2 of the lock washer tabs.



Hide 35572 80.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH

a.
C170829

Install the control shaft lever with the washer and nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)