CHECK ECM
Each ECM terminal standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A38-21 (L4) - C45-81 (E1) | BR-R - BR | Transfer L4 position signal | ·
Engine switch on (IG) ·
Transfer position switch on L4 |
Below 1.5 V |
·
Engine switch on (IG) ·
Transfer position switch not on L4 |
11 to 14 V | |||
| A38-5 (TFN) - C45-81 (E1) | G - BR | Transfer neutral position signal | ·
Engine switch on (IG) ·
Transfer position in neutral |
Below 1.5 V |
·
Engine switch on (IG) ·
Transfer position not in neutral |
11 to 14 V | |||
| C45-120 (NSW) - C45-81 (E1) | L - BR | PNP switch signal | ·
Engine switch on (IG) ·
Shift lever in P or N |
Below 1.5 V |
·
Engine switch on (IG) ·
Shift lever not in P or N |
11 to 14 V | |||
| C45-2 (P) - C45-81 (E1) | G-B - BR | P shift position switch signal | ·
Engine switch on (IG) ·
Shift lever in P |
11 to 14 V |
·
Engine switch on (IG) ·
Shift lever not in P |
Below 1.5 V | |||
| C45-26 (R) - C45-81 (E1) | L-R - BR | R shift position switch signal | ·
Engine switch on (IG) ·
Shift lever in R |
11 to 14 V |
·
Engine switch on (IG) ·
Shift lever not in R |
Below 1.5 V | |||
| C45-25 (N) - C45-81 (E1) | G-W - BR | N shift position switch signal | ·
Engine switch on (IG) ·
Shift lever in N |
11 to 14 V |
·
Engine switch on (IG) ·
Shift lever not in N |
Below 1.5 V | |||
| C45-27 (D) - C45-81 (E1) | G - BR | D shift position switch signal | ·
Engine switch on (IG) ·
Shift lever in D |
11 to 14 V |
·
Engine switch on (IG) ·
Shift lever not in D |
Below 1.5 V | |||
| A38-25 (S) - C45-81 (E1) | W - BR | S shift position switch signal | ·
Engine switch on (IG) ·
Shift lever in S |
11 to 14 V |
·
Engine switch on (IG) ·
Shift lever not in S |
Below 1 V | |||
| A38-38 (SFTU) - C45-81 (E1) | V - BR
Y - BR* |
Up-shift shift position switch signal | ·
Engine switch on (IG) ·
Shift lever in S |
11 to 14 V |
·
Engine switch on (IG) ·
Shift lever in "+" position (up-shift) |
Below 1 V | |||
| A38-27 (SFTD) - C45-81 (E1) | L - BR | Down-shift position switch signal | ·
Engine switch on (IG) ·
Shift lever in S |
11 to 14 V |
·
Engine switch on (IG) ·
Shift lever in "-" position (down-shift) |
Below 1 V | |||
| A38-36 (STP) - C45-81 (E1) | R - BR | Stop light switch signal | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| C45-7 (S1) - C45-81 (E1) | R - BR | Shift solenoid valve S1 signal | Engine switch on (IG) | 11 to 14 V |
| 1st or 2nd gear | 11 to 14 V | |||
| 3rd, 4th or 5th gear | Below 1.5 V | |||
| C45-4 (S2) - C45-81 (E1) | W - BR | Shift solenoid valve S2 signal | Engine switch on (IG) | Below 1.5 V |
| 2nd or 3rd gear | 11 to 14 V | |||
| 1st, 4th or 5th gear | Below 1.5 V | |||
| C45-6 (SR) - C45-81 (E1) | G - BR | Shift solenoid valve SR signal | Engine switch on (IG) | Below 1.5 V |
| 5th gear | 11 to 14 V | |||
| 1st gear | Below 1 V | |||
| C45-14 (SL1+) - C45-15 (SL1-) | Y - L | Shift solenoid valve SL1 signal | Engine idling | Pulse generation |
| C45-12 (SL2+) - C45-13 (SL2-) | G-R - L-W | Shift solenoid valve SL2 signal | Engine idling | Pulse generation |
| C45-9 (SLT+) - C45-8 (SLT-) | B - G-B | Shift solenoid valve SLT signal | Engine idling | Pulse generation |
| C45-10 (SLU+) - C45-11 (SLU-) | L-Y - L-R | Shift solenoid valve SLU signal | 4th (lock-up) gear or 5th (lock-up) gear | Pulse generation |
| C45-122 (THO1) - C45-97 (ETHW) | G-Y - BR | No. 1 ATF temperature sensor signal | No. 1 ATF temperature: 115°C (239°F) or higher | Below 1.5 V |
| C45-99 (THO2) - C45-97 (ETHW) | L - BR | No. 2 ATF temperature sensor signal | No. 2 ATF temperature: 115°C (239°F) or higher | Below 1.5 V |
| C45-101 (SP2+) - C45-100 (SP2-) | Y - B | Speed sensor SP2 signal | Vehicle speed 20 km/h (12 mph) | Pulse generation
(see waveform 1) |
| C45-124 (NT+) - C45-123 (NT-) | Y - B | Speed sensor NT signal | Engine idling
(Shift lever in P or N) |
Pulse generation
(see waveform 2) |
| A38-10 (CANH) - C45-81 (E1) | P - BR | CAN communication line | Engine switch on (IG) | Pulse generation
(see waveform 3) |
| A38-11 (CANL) - C45-81 (E1) | B - BR | CAN communication line | Engine switch on (IG) | Pulse generation
(see waveform 4) |
| A38-51 (PWR) - C45-81 (E1) | L-B - BR | Pattern select (PWR) switch signal | ·
Engine switch on (IG) ·
Pattern select (PWR) switch off |
11 to 14 V |
·
Engine switch on (IG) ·
Pattern select (PWR) switch on |
Below 1.5 V | |||
| A38-4 (SNWI) - C45-81 (E1) | P - BR
R - BR* |
Pattern select (2ND) switch signal | ·
Engine switch on (IG) ·
Pattern select (2ND) switch off |
11 to 14 V |
·
Engine switch on (IG) ·
Pattern select (2ND) switch continuously pressed |
Below 1.5 V |
*: GRJ200L-GNANKC
Using an oscilloscope, check waveform 1.
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C45-101 (SP2+) - C45-100 (SP2-) | 2 V/DIV., 20 msec./DIV. | Vehicle speed 20 km/h (12 mph) |
Using an oscilloscope, check waveform 2.
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C45-124 (NT+) - C45-123 (NT-) | 1 V/DIV., 2 msec./DIV. | Engine idling (Shift lever in P or N) |
Using an oscilloscope, check waveform 3.
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| A38-10 (CANH) - C45-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine switch on (IG) |
Using an oscilloscope, check waveform 4.
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| A38-11 (CANL) - C45-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine switch on (IG) |