Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255290 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P0717  Turbine Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC Code DTC Detection Condition Trouble Area
P0717 All the conditions below are detected for 5 sec. or more (1 trip detection logic).
(a) Gear change is not performed.
(b) The gear position is 4th or 5th.
(c) The T/M input shaft rpm is 300 rpm or less.
(d) The T/M output shaft rpm is 1000 rpm or more.
(e) The park/neutral position switch:
·

The NSW input signal is OFF.

·

The R input signal is OFF.


(f) The shift solenoid valves and park/neutral position switch are operating normally.
·

Open or short in speed sensor NT circuit

·

Speed sensor NT

·

ECM

·

Automatic transmission (clutch, brake or gear, etc.)



Reference: Inspect using an oscilloscope.

Check the waveform of the ECM connector.

Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition
C45-124 (NT+) - C45-123 (NT-) 1 V/DIV., 2 msec./DIV. Engine idling (shift lever in P or N) Refer to illustration


C175014E01
2.501,0.811 3.157,1.012 0.656,0.201 10 1 V/DIV. 2.646,1.576 3.057,1.779 0.411,0.202 10 GND 1.338,2.649 2.293,2.836 0.956,0.188 10 2 msec./DIV.

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor NT (input RPM). The ECM outputs a gear shift signal comparing the input speed sensor NT with the output speed sensor SP2.

While the vehicle is operating in the 4th or 5th gear position with the shift lever in D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
·

*1: Pulse is not output or is irregularly output.

·

*2: The vehicle speed is approximately 50 km/h (31 mph) or more.



WIRING DIAGRAM

C258073E15
1.278,2.058 1.525,2.245 0.247,0.187 10 2 1.278,1.242 1.525,1.428 0.247,0.187 10 1 0.826,2.365 1.187,2.552 0.360,0.187 10 C35 5.618,1.069 5.978,1.256 0.360,0.187 10 NT+ 5.242,1.216 5.584,1.403 0.342,0.187 10 124 5.618,2.199 5.978,2.385 0.360,0.187 10 NT- 5.781,2.993 6.239,3.179 0.458,0.187 10 C45 5.781,3.175 6.239,3.362 0.458,0.187 10 ECM 5.242,2.346 5.584,2.532 0.342,0.187 10 123 0.826,2.558 2.074,2.745 1.247,0.187 10 Speed Sensor NT

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up:
·

ON (after warming up engine): Input turbine speed (NT) equal to engine speed

·

OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed


The data is displayed in increments of 50 rpm.

HINT:
·

SPD (NT) is always 0 while driving:

Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:

Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR NT INSTALLATION
a.
C211922E03
0.833,0.156 1.073,0.354 0.24,0.198 10 *a 2.302,0.156 2.542,0.354 0.24,0.198 10 *b

Check the speed sensor NT installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.


Text in Illustration
*a CORRECT
b INCORRECT



OK

2.INSPECT SPEED SENSOR NT

NG

SECURELY INSTALL OR REPLACE SPEED SENSOR NT

2.INSPECT SPEED SENSOR NT
a.
C206284E07
0.056,0.003 0.296,0.205 0.240,0.202 10 *a 1.303,1.682 1.603,1.103 false 1.196,1.707 1.643,1.909 0.446,0.202 10 2 2.15,1.682 1.852,1.103 false 2.152,1.707 2.598,1.909 0.446,0.202 10 1

Disconnect the speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω


Text in Illustration
*a Component without harness connected
(Speed Sensor NT)



OK

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)
a.
U165057E02
1.625,1.333 1.302,1.698 false 1.708,1.333 2.031,1.698 false 0.094,0.042 0.385,0.25 0.292,0.208 10 false *a 1.448,0.302 1.823,0.531 0.375,0.229 10 false C45 0.938,1.729 1.552,1.896 0.615,0.167 10 false 123 (NT-) 1.813,1.729 2.542,1.896 0.729,0.167 10 false 124 (NT+)

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-124 (NT+) - C45-123 (NT-) 20°C (68°F) 560 to 680 Ω
C45-124 (NT+) - Body ground Always 10 kΩ or higher
C45-123 (NT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR