Shifting from 1st to 5th is performed in combination with the "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, S1, S2 and SR which is controlled by the ECM. If an open or short circuit occurs in one of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (In case of an open or short circuit, the ECM stops sending current to the circuit. For details, refer to the Fail-Safe Chart (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>FAIL-SAFE CHART)).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0973 | The ECM detects a short in the solenoid valve S1 circuit 2 times when the solenoid valve S1 is operated (1 trip detection logic). | ·
Short in shift solenoid valve S1 circuit ·
Shift solenoid valve S1 ·
ECM |
| P0974 | The ECM detects an open in the solenoid valve S1 circuit 2 times when the solenoid valve S1 is not operated (1 trip detection logic). | ·
Open in shift solenoid valve S1 circuit ·
Shift solenoid valve S1 ·
ECM |
These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When the shift solenoid valve S1 is on, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S1 circuit.
When the shift solenoid valve S1 is off, if its resistance is 100 kΩ or higher, the ECM determines there is an open in the shift solenoid valve S1 circuit (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>FAIL-SAFE CHART).
The shift solenoid valve S1 turns ON/OFF normally when the shift lever is in D.
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th |
| Shift solenoid valve S1 | ON | ON | OFF | OFF | OFF |
Disconnect the transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (S1) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| *a | Component without harness connected
(Transmission Wire) |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C45-7 (S1) - Body ground | 20°C (68°F) | 11 to 15 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Remove the shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve S1 connector ·
Battery negative (-) → Shift solenoid valve S1 body |
Valve moves and makes an operating noise |
| *a | Component without harness connected
(Shift Solenoid Valve S1) |
OK
NG