Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255290 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

C261119E02
4.875,2.313 5.177,1.417 5.177,1.417 5.25,1.417 false 5.094,2.469 5.229,2.875 5.229,2.875 5.302,2.875 false 5.854,2.531 5.969,2.875 5.969,2.875 6.031,2.875 false 6.104,2.802 6.99,3.021 0.885,0.219 10 false Solenoid Coil 0.042,0.646 1.292,0.865 1.25,0.219 10 false Hydraulic Pressure 2.521,3 3.083,3.219 0.563,0.219 10 false Current 5.375,2.792 5.906,3.01 0.531,0.219 10 false Sleeve 5.333,1.333 6.167,1.552 0.833,0.219 10 false Spool Valve

The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current of the SLT solenoid valve to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC Code DTC Detection Condition Trouble Area
P2716 An open or short is detected in the shift solenoid valve SLT circuit for 1 sec. or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C219459E09
5.739,1.181 6.140,1.370 0.400,0.190 10 SLT+ 5.739,2.398 6.140,2.587 0.400,0.190 10 SLT- 2.345,1.061 2.746,1.250 0.400,0.190 10 SLT+ 2.345,2.279 2.746,2.468 0.400,0.190 10 SLT- 5.953,3.37 6.353,3.560 0.400,0.190 10 ECM 5.952,3.199 6.353,3.389 0.400,0.190 10 C45 2.801,2.508 2.993,2.698 0.192,0.190 10 6 2.801,1.291 2.993,1.481 0.192,0.190 10 14 5.533,1.291 5.769,1.481 0.236,0.190 10 9 5.533,2.508 5.725,2.698 0.192,0.190 10 8 1.019,1.741 2.596,1.931 1.576,0.190 10 Shift Solenoid Valve SLT 0.93,3.099 2.521,3.289 1.590,0.190 10 Transmission Wire 0.93,2.925 1.331,3.114 0.400,0.190 10 C34 0.805,1.393 0.997,1.582 0.192,0.190 10 2 0.8,2.171 0.992,2.360 0.192,0.190 10 1

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C214326E66
1.429,1.282 1.22,1.745 false 1.524,1.061 1.779,1.745 false 0.983,1.783 1.346,1.950 0.363,0.167 10 SLT+ 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 1.639,1.783 1.981,1.950 0.343,0.167 10 SLT-

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SLT+) - 6 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
14 (SLT+) - Body ground Always 10 kΩ or higher
6 (SLT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U165061E02
0.781,1.74 1.198,0.854 false 1.271,0.854 1.75,1.75 false 0.094,0.021 0.385,0.229 0.292,0.208 10 false *a 1.469,0.313 1.844,0.542 0.375,0.229 10 false C45 0.5,1.781 1.219,1.979 0.719,0.198 10 false 8 (SLT-) 1.563,1.792 2.188,1.99 0.625,0.198 10 false 9 (SLT+)

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-9 (SLT+) - C45-8 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C45-9 (SLT+) - Body ground Always 10 kΩ or higher
C45-8 (SLT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928E21
1.75,0.979 2.198,0.396 false 1.49,0.979 1.031,0.396 false 1.75,2.969 2.198,2.375 false 1.49,2.969 1.031,2.375 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.125,4.125 0.198,0.198 10 false (-) 1.115,3.927 1.333,4.125 0.219,0.198 10 false (+)

Remove the shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLT)


OK

NG