Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255290 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) J

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  Pattern Select Switch Power Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and power shift patterns and lock-up pattern.

By following the programs corresponding to the signals from the pattern select switch, the park/neutral position switch and other various sensors, the ECM switches the solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM

C176075E10
2.125,2.958 3.885,3.156 1.76,0.198 10 false Suspension Control Switch 5.229,1.469 5.5,1.667 0.271,0.198 10 false 51 5.5,1.354 6.344,1.635 0.844,0.281 10 false PWR 5.302,2.396 5.573,2.594 0.271,0.198 10 false 4 5.5,2.292 6.469,2.615 0.969,0.323 10 false SNWI 3.708,1.5 3.979,1.698 0.271,0.198 10 false 16 3.521,1.26 3.698,1.469 0.177,0.208 10 false P 3.719,2.427 3.99,2.625 0.271,0.198 10 false 17 2.135,2.406 2.406,2.604 0.271,0.198 10 false 20 3.354,2.177 3.656,2.385 0.302,0.208 10 false 2ND 2.396,2.177 2.552,2.385 0.156,0.208 10 false E 5.677,3.073 5.948,3.271 0.271,0.198 10 false A38 5.656,3.26 6.052,3.448 0.396,0.188 10 false ECM 2.125,2.771 2.458,2.958 0.333,0.188 10 false V4

CAUTION / NOTICE / HINT

When the pattern select (PWR) switch is pushed, switch contact is made and power mode is selected. To cancel power mode, push the pattern select (PWR) switch once again.

PROCEDURE

1.INSPECT PATTERN SELECT (PWR) SWITCH
a.
C238423E15
1.865,1.781 1.625,1.323 false 0.771,1.781 1.042,1.323 false 0.052,0 0.25,0.198 0.198,0.198 10 false *a 1.896,1.76 2.083,1.958 0.188,0.198 10 false P 0.656,1.771 0.833,1.969 0.177,0.198 10 false E

Remove the suspension control switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
16 (P) - 20 (E) Pattern select (PWR) switch on Below 1 Ω
16 (P) - 20 (E) Pattern select (PWR) switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Suspension Control Switch)



OK

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)

NG

REPLACE PATTERN SELECT (PWR) SWITCH (SUSPENSION CONTROL SWITCH)

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - BODY GROUND)
a.
U165078E02
2.5,1.74 2.354,1.417 false 2.531,1.74 2.698,1.938 0.167,0.198 10 false E 0.052,0 0.25,0.198 0.198,0.198 10 false *a 0.354,1.031 0.729,1.26 0.375,0.229 10 false V4

Disconnect the suspension control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-20 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Suspension Control Switch)



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (PWR) SWITCH - ECM)
U164936E02
1.5,1.792 1.646,1.323 false 0.063,0 0.375,0.198 0.313,0.198 10 false *a 1.625,0.281 2,0.51 0.375,0.229 10 false A38 1.198,1.844 1.875,2.042 0.677,0.198 10 false 51 (PWR)

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-51 (PWR) - Body ground Pattern select (PWR) switch on Below 1 Ω
A38-51 (PWR) - Body ground Pattern select (PWR) switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR