Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255295 SHIFT LEVER G

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 1.INSPECT SHIFT LOCK SOLENOID

a.
C150404E12
1.155,2.022 1.277,2.188 0.122,0.167 10 1 1.501,2.022 1.623,2.188 0.122,0.167 10 2 1.841,2.022 1.963,2.188 0.122,0.167 10 3 2.195,2.022 2.317,2.188 0.122,0.167 10 4 0.055,0.007 0.266,0.233 0.211,0.226 10 *a 1.967,0.721 2.341,0.941 0.373,0.220 10 SLS- 0.339,0.768 0.734,0.957 0.395,0.189 10 SLS+ 2.211,2.839 2.359,3.012 0.148,0.173 10 P 1.774,2.842 2.005,3.015 0.231,0.173 10 E2 1.222,1.976 0.981,0.85 0.981,0.85 0.814,0.85 false 1.557,1.978 1.699,0.796 1.699,0.796 1.952,0.796 false 1.893,2.254 1.893,2.827 false 2.257,2.256 2.257,2.829 false

Disconnect the shift lock solenoid connector from the shift lock control ECU.

Text in Illustration
*a Component with harness connected
(Shift Lock Solenoid)


b.

Measure the resistance according to the values in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 101 to 123 Ω
3 (E2) - 4 (P) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω



c.

Apply 12 V battery voltage to the shift lock solenoid and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Terminal 1 (SLS+)

·

Battery negative (-) → Terminal 2 (SLS-)


Solenoid moves and makes an operating noise


If the result is not as specified, replace the shift lever assembly.


Hide 84722 2.INSPECT TRANSMISSION CONTROL SWITCH

C146679E36
1.594,1.281 1.271,0.604 1.271,0.604 1.094,0.604 true 1.031,2.323 1.031,2.01 1.031,2.01 1.573,1.594 true 1.781,1.271 2.115,0.573 2.115,0.573 2.354,0.573 true 2,1.344 2.677,1.344 true 2.75,2.281 2.75,2.083 2.75,2.083 2.01,1.563 true 0.135,0.135 0.427,0.375 0.292,0.24 10 false *a 0.885,0.531 1.135,0.729 0.25,0.198 10 false IG 1.01,2.385 1.177,2.583 0.167,0.198 10 false S 2.479,0.49 2.99,0.688 0.51,0.198 10 false SFTU 2.719,1.25 3.229,1.448 0.51,0.198 10 false SFTD 2.708,2.302 2.885,2.5 0.177,0.198 10 false E

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
2 (SFTU) - 5 (E) Shift lever held in "+" (Up-shift)
1 (SFTD) - 5 (E) Shift lever held in "-" (Down-shift)
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever not held in "+" (Up-shift)
1 (SFTD) - 5 (E) Shift lever not held in "-" (Down-shift)


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)

If the result is not as specified, replace the transmission floor shift assembly.