Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TORQUE CONVERTER CLUTCH AND DRIVE PLATE › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255302 TORQUE CONVERTER CLUTCH AND DRIVE PLATE G

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER CLUTCH AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

a.

Inspect the one-way clutch.

i.
D029376E06
0.604,0.552 1.406,0.625 true 0.604,0.552 1.49,0.781 true 0.333,0.469 0.667,0.656 0.333,0.188 10 false SST

Install SST into the inner race of the one-way clutch.

SST
09350-32014  (09351-32010)


ii.

Set SST so that it fits in the notch of the torque converter hub and the outer race of the one-way clutch.

SST
09350-32014  (09351-32020)


iii.
C344852E01
1.777,0.258 2.058,0.451 0.281,0.193 10 *a 1.851,1.616 2.132,1.808 0.281,0.193 10 *b 1.737,0.939 2.367,0.619 2.367,0.619 2.275,0.808 false 2.419,0.47 2.741,0.649 0.323,0.179 10 SST

With the torque converter assembly standing on its side, check that the clutch locks when SST is turned counterclockwise and rotates freely and smoothly when SST is turned clockwise.

Text in Illustration
*a Hold
*b Turn
V113147

Difficult
V113148

Smooth

If the results are not as specified, clean the torque converter assembly and recheck the one-way clutch.

If the results still are not as specified even after cleaning the torque converter assembly, replace the torque converter assembly.



b.
C197457E03
0.113,0.051 0.341,0.247 0.228,0.195 10 *a

Determine the condition of the torque converter assembly.

Text in Illustration
*a Sample showing maximum allowable amount of powder in ATF

i.

Check that the following conditions are met:

·

During the stall test or when the shift lever is in N, metallic sounds are not emitted from the torque converter assembly.

·

The one-way clutch turns in one direction and locks in the other direction.

·

The amount of powder in the ATF is not more than the sample shown in the illustration.


If the results are not as specified, replace the torque converter assembly.

HINT:

The sample illustration shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF taken from a removed torque converter assembly.




c.

Replace the ATF in the torque converter assembly.

i.

If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter assembly thoroughly and drain the ATF with the torque converter assembly facing upward.



d.
D025368E77
1.729,1.823 2.208,1.052 true 2.219,0.938 2.438,1.125 0.219,0.188 10 false *c 0.49,0.115 0.698,0.292 0.208,0.177 10 false *a 1.531,0.115 1.698,0.271 0.167,0.156 10 false *b

Prevent deformation of the torque converter and damage to the oil pump gear.

Text in Illustration
*a CORRECT
*b INCORRECT
*c Bottom is damaged

i.

When any marks due to interference are found on the end of a bolt for the torque converter assembly and on the bottom of the bolt hole, replace the bolt and torque converter assembly.


ii.

Make sure all of the bolts are the same length.


iii.

Make sure no spring washers are missing.



Hide 2.INSPECT DRIVE PLATE

a.
C193528E11
3.146,0.656 3.26,0.833 0.115,0.177 10 true 5 2.615,0.031 2.729,0.208 0.115,0.177 10 true 4 1.854,0.031 1.969,0.208 0.115,0.177 10 true 3 1.521,0.708 1.635,0.885 0.115,0.177 10 true 2 0.667,1.844 0.896,2.031 0.229,0.188 10 false *a 2.302,1.542 2.448,1.74 0.146,0.198 10 true 1 3.104,1.24 3.25,1.417 0.146,0.177 10 true 6

Check the drive plate for damage.


b.

Set up a dial indicator and measure the runout of the 6 portions around the torque converter contact surfaces.

Maximum runout:

0.30 mm (0.0118 in.)


Text in Illustration
*a Measuring Point

If the runout is more than the maximum or if the drive plate is damaged, replace the drive plate (See page Engine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION).