Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM J

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

The transmission control switch detects when the shift lever is moved to S.

Using the transmission control switch, when the shift lever is in S, it is possible to select between 1st and 8th gears (S1 to S8).

Moving the shift lever to "+" once selects the next higher gear, and moving the shift lever to "-" once selects the next lower gear.

WIRING DIAGRAM

C343214E01
5.618,2.534 6.138,2.736 0.520,0.202 10 S 5.618,1.945 6.138,2.147 0.520,0.202 10 SFTU 5.618,1.356 6.138,1.558 0.520,0.202 10 SFTD 6.493,1.161 7.014,1.363 0.520,0.202 10 12 V 5.324,2.534 5.604,2.736 0.281,0.202 10 27 5.324,1.945 5.604,2.147 0.281,0.202 10 39 5.324,1.356 5.604,1.558 0.281,0.202 10 47 4.086,2.534 4.367,2.736 0.281,0.202 10 7 4.086,1.945 4.307,2.147 0.220,0.202 10 2 4.086,1.356 4.307,1.558 0.220,0.202 10 1 3.868,2.534 4.389,2.736 0.520,0.202 10 S 3.602,1.945 4.123,2.147 0.520,0.202 10 SFTU 3.602,1.356 4.123,1.558 0.520,0.202 10 SFTD 2.742,2.534 3.262,2.736 0.520,0.202 10 IG 2.742,1.356 3.262,1.558 0.520,0.202 10 E 2.542,2.534 2.823,2.736 0.281,0.202 10 3 2.542,1.356 2.823,1.558 0.281,0.202 10 5 0.415,2.637 2.078,2.839 1.664,0.202 10 from ECU-IG NO. 2 Fuse 6.017,5.035 6.537,5.237 0.520,0.202 10 A38 6.017,5.221 6.537,5.423 0.520,0.202 10 ECM 3.18,4.84 3.700,5.042 0.520,0.202 10 TCM 0.427,5.397 2.919,5.599 2.493,0.202 10 : CAN Communication Line 2.451,3.136 2.851,3.338 0.400,0.202 10 E52 2.451,3.323 4.532,3.525 2.081,0.202 10 Transmission Control Switch 6.493,1.746 7.014,1.948 0.520,0.202 10 12 V

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport (S) mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-


Result
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B


A

2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)

B

6.INSPECT TRANSMISSION CONTROL SWITCH
2.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever in "+" (up-shift)

·

OFF: Shift lever not in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever in "-" (down-shift)

·

OFF: Shift lever not in "-" (down-shift)


-


Result
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B


A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

3.INSPECT TRANSMISSION CONTROL SWITCH
3.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E55
2.146,0.323 1.813,0.76 true 1.958,0.781 2.438,0.615 true 1.948,0.958 2.333,1.125 true 0.052,0.073 0.365,0.271 0.313,0.198 10 false *a 2.198,0.177 2.688,0.365 0.49,0.188 10 false SFTU 2.385,1.104 2.573,1.302 0.188,0.198 10 false E 2.531,0.49 3.021,0.677 0.49,0.188 10 false SFTD

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SFTU) - 5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
2 (SFTU) - 5 (E) Shift lever not held in "+" 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever not held in "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
U156205E01
1.104,1.667 1.5,1.354 false 0.083,0.031 0.396,0.229 0.313,0.198 10 false *a 0.552,1 0.927,1.229 0.375,0.229 10 false E52 0.948,1.552 1.104,1.75 0.156,0.198 10 false E

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-5 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U156200E05
2.188,1.188 2.604,1.76 true 2.188,1.271 1.833,1.771 true 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 1.375,1.802 2.146,1.99 0.771,0.188 10 false 47 (SFTD) 2.333,1.792 3.083,1.99 0.75,0.198 10 false 39 (SFTU) 1.667,0.281 2.021,0.458 0.354,0.177 10 false A38

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-39 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
A38-47 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
A38-39 (SFTU) - Body ground Shift lever not held in "+" 10 kΩ or higher
A38-47 (SFTD) - Body ground Shift lever not held in "-" 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E56
1.615,0.74 1.021,0.302 true 1.01,1.417 1.604,0.99 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.844,0.167 1.156,0.365 0.313,0.198 10 false IG 0.896,1.344 1.083,1.542 0.188,0.198 10 false S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "- " Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
U156206E01
1.792,1.094 2.333,0.781 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.406,0.667 2.719,0.865 0.313,0.198 10 false IG 0.542,1 0.917,1.229 0.375,0.229 10 false E52

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
E52-3 (IG) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the E52 transmission control switch connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E52-7 (S) - A38-27 (S) Always Below 1 Ω
E52-7 (S) - Body ground Always 10 kΩ or higher
A38-27 - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR