Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

Refer to DTC P0711 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>P0711).

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0712
1.

The battery voltage is 9.5 V or higher.

2.

No. 1 ATF temperature sensor voltage is below 0.08 V

3.

60 seconds

4.

1-trip detection logic


·

Short in No. 1 ATF temperature sensor circuit

·

No. 1 ATF temperature sensor (transmission wire)

·

TCM


P0713
1.

The battery voltage is 9.5 V or higher, engine speed is more than 400 rpm and shift lever in D.

2.

No. 1 ATF temperature sensor voltage is higher than 4.94 V

3.

12 seconds

4.

1-trip detection logic


·

Open in No. 1 ATF temperature sensor circuit

·

No. 1 ATF temperature sensor (transmission wire)

·

TCM



MONITOR DESCRIPTION

The No. 1 ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the No. 1 ATF temperature sensor circuit. If the resistance value of the No. 1 ATF temperature sensor is below 79 Ω*1 or higher than 156 kΩ*2, the TCM interprets this as a fault in the No. 1 ATF temperature sensor or wiring. The TCM will illuminate the MIL and store the DTC.

HINT:
·

*1: 171°C (339.8°F) or higher is indicated regardless of the actual ATF temperature.

·

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

·

The ATF temperature can be checked on the GTS display.



WIRING DIAGRAM

C311451E23
1.5,1.74 3.542,1.99 2.042,0.25 10 false No. 1 ATF Temperature Sensor 1.604,2.677 2.052,2.875 0.448,0.198 10 false C171 1.604,2.833 3.052,3.021 1.448,0.188 10 false Transmission Wire 5.583,3.115 6.073,3.354 0.49,0.24 10 false TCM 5.594,2.938 6.052,3.135 0.458,0.198 10 false A80 3.531,1.156 3.99,1.354 0.458,0.198 10 false OT+ 3.563,2.104 3.948,2.292 0.385,0.188 10 false OT- 3.896,2.115 4.354,2.313 0.458,0.198 10 false 2 3.896,1.156 4.354,1.354 0.458,0.198 10 false 1 4.938,1.156 5.396,1.354 0.458,0.198 10 false 23 4.938,2.115 5.396,2.313 0.458,0.198 10 false 24 5.156,2.115 5.615,2.313 0.458,0.198 10 false E2 5.156,1.156 5.615,1.354 0.458,0.198 10 false THO1 5.865,0.927 6.156,1.146 0.292,0.219 10 false 5V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Start the engine.

2.

Wait for 60 seconds or more with the shift lever in D.



DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List / A/T Oil Temperature 1.


g.

According to the display on the GTS, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 171°C (339.8°F)
·

After stall speed test: Approximately 80°C (176°F)

·

While engine is cold: Equal to ambient temperature


If value is -40°C (-40°F) or 171°C (339.8°F), No. 1 ATF temperature sensor circuit is open or short circuited.

HINT:
·

When DTC P0712 is output and the GTS shows 171°C (339.8°F) or higher, there is a short circuit.

·

When DTC P0713 is output and the GTS shows -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the GTS in order to check if a malfunction exists.



Temperature Displayed Malfunction
-40°C (-40°F) Open or short circuit
171°C (339.8°F) or higher Short circuit

HINT:

If a circuit related to the No. 1 ATF temperature sensor becomes open, P0713 will be stored in approximately 0.5 seconds. It is not necessary to inspect the circuit when P0711 is output.




PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE 1)
a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List / A/T Oil Temperature 1.


g.

According to the display on the GTS, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 171°C (339.8°F)
·

After stall speed test: Approximately 80°C (176°F)

·

While engine is cold: Equal to ambient temperature


If value is -40°C (-40°F) or 171°C (339.8°F), No. 1 ATF temperature sensor circuit is open or short circuited

Result
Result Proceed to
Data List value is not within the normal condition A
Data List value is within the normal condition B



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 ATF TEMPERATURE SENSOR - TCM)

B

2.CHECK HARNESS AND CONNECTOR (NO. 1 ATF TEMPERATURE SENSOR - TCM)
a.
U165632E02
1.344,2.083 1.781,2.938 true 1.271,2.083 0.833,2.938 true 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 1.479,2.99 2.25,3.177 0.771,0.188 10 false 23 (THO1) 0.552,2.969 1.156,3.156 0.604,0.188 10 false 24 (E2) 0.854,0.177 1.208,0.354 0.354,0.177 10 false A80

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-23 (THO1) - A80-24 (E2) Always 79 Ω to 156 kΩ
A80-23 (THO1) - Body ground Always 10 kΩ or higher
A80-24 (E2) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.


ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ


Text in Illustration
*a Rear view of wire harness connector
(to TCM)


OK

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C171 transmission wire connector.


b.

Disconnect the A80 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C171-1 (OT+) - A80-23 (THO1) Always Below 1 Ω
C171-2 (OT-) - A80-24 (E2) Always Below 1 Ω
C171-1 (OT+) or A80-23 (THO1) - Body ground Always 10 kΩ or higher
C171-2 (OT-) or A80-24 (E2) - Body ground Always 10 kΩ or higher




OK

REPLACE NO. 1 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR