Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The ECM communicates with the TCM via the Controller Area Network (CAN).

If there is a problem in communication, the TCM stores this DTC.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
U0100
1.

Battery voltage is 9.5 V or higher.

2.

No communication between the ECM and TCM

3.

1.25 seconds

4.

1-trip detection logic


·

Harness or connector

·

ECM

·

TCM



WIRING DIAGRAM

C312032E11
6.031,2.927 6.438,3.167 0.406,0.24 10 false TCM 0.75,2.75 1.24,2.979 0.49,0.229 10 false ECM 5.729,0.604 6.344,0.802 0.615,0.198 10 false CAN+ 5.729,1.052 6.344,1.25 0.615,0.198 10 false CAN- 0.99,0.604 1.604,0.802 0.615,0.198 10 false CANP 1.021,1.063 1.635,1.26 0.615,0.198 10 false CANP 1.146,1.51 1.458,1.708 0.313,0.198 10 false +B 1.094,1.896 1.49,2.094 0.396,0.198 10 false +B2 1.177,2.271 1.49,2.469 0.313,0.198 10 false E1 1.469,0.625 1.813,0.823 0.344,0.198 10 false A38 6.042,2.76 6.5,2.958 0.458,0.198 10 false A82 5.469,0.458 5.781,0.656 0.313,0.198 10 false 1 0.792,3.406 2.583,3.615 1.792,0.208 10 false : CAN Communication Line 2.99,1.885 4.896,2.167 1.906,0.281 10 false from EFI MAIN NO. 1 Relay 5.469,0.906 5.781,1.104 0.313,0.198 10 false 2 1.5,0.438 1.813,0.635 0.313,0.198 10 false 10 1.51,0.875 1.667,1.073 0.156,0.198 10 false 18 1.542,1.333 1.698,1.531 0.156,0.198 10 false 2 1.531,1.719 1.688,1.917 0.156,0.198 10 false 3 1.469,1.063 1.813,1.26 0.344,0.198 10 false A38 1.469,1.51 1.813,1.708 0.344,0.198 10 false A38 1.469,1.906 1.813,2.104 0.344,0.198 10 false A38 1.469,2.271 1.781,2.469 0.313,0.198 10 false C45 1.51,2.083 1.667,2.281 0.156,0.198 10 false 81

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:
·

If the CAN communication system malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM is not updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.

·

The malfunctioning area can be checked using the CAN Bus Check function on the GTS.

·

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Check the battery voltage is 9.5 V or higher.

(b)

Turn the engine switch on (IG).




PROCEDURE

1.INSPECT ECM
a.
U156199E04
1.719,0.875 2.156,1.729 true 1.646,0.865 1.208,1.719 true 0.125,0 0.406,0.177 0.281,0.177 10 false *a 0.958,1.76 1.563,2.01 0.604,0.25 10 false 2 (+B) 1.917,1.771 2.521,2.01 0.604,0.24 10 false 3 (+B2) 1.667,0.281 2.021,0.458 0.354,0.177 10 false A38

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
A38-3 (+B2) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

GO TO ECM POWER SOURCE CIRCUIT (ENGINE CONTROL SYSTEM / SFI SYSTEM)

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
U165696E02
1.948,1.208 2.146,1.719 true 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2,1.729 2.583,1.917 0.583,0.188 10 false 81 (E1) 1.469,0.271 1.823,0.448 0.354,0.177 10 false C45

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the A82 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-10 (CANP) - A82-1 (CAN+) Always Below 1 Ω
A38-18 (CANN) - A82-2 (CAN-) Always Below 1 Ω
A38-10 (CANP) or A82-1 (CAN+) - Body ground Always 10 kΩ or higher
A38-18 (CANN) or A82-2 (CAN-) - Body ground Always 10 kΩ or higher




OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM

NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Start the engine.


c.

Read the DTCs (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs are not output A
DTC U0100 is output B



A

END

B